Thanks a lot Paul!
I did notice the attributes needed on my properties, the
OnDataBinding too!!
There was a nice article by Miguel Castro on the
Code-Magazine and it helped
a lot in fact!!
Developing Controls is quiet interesting and nice!!
Regards
On 12/4/06, Paul Glavich <glav aspalliance.com> wrote:
>
> Sounds like its not properly being serialised and/or
parsed within the
> designer.
>
> Make sure when you set the properties, the appropriate
markup is set in
> the
> source view. Additionally, make sure your code parses
this markup
> correctly
> (I suspect this is where its not working). So when it
reads the markup
> that
> defines the control, its not properly reading the
values and setting these
> properties.
>
> - Glav
>
> -----Original Message-----
> From: Bilal Haidar [MVP] [mailto:bhaidargmail.com]
> Sent: Saturday, 2 December 2006 2:32 AM
> To: aspnet-controlbuildingaspadvice.com
> Subject: [aspnet-controlbuilding] RE: Composite Control
>
> Hello Fred:
>
> What I have is a ListBox within a composite control. I
have exposed the
> whole control via a proeprty. So, if I change for
example the Items
> property, they are shown now on the IDE, but when I run
the page, the
> items
> inside the ListBox which is inside the composite
control are not shown!
>
> I have read some articles today which says, it is
better not to expose the
> whole list as a proeprty but rather selective
properties!!
>
> Thanks
>
>
> On 12/1/06, Fred Hartzler <fredfhcc.com> wrote:
> >
> > I program in Delphi. If I add items to a list in
the designer, they are
> > added to the aspx source. Do you see the items
there?
> >
> > In general, when data is not displayed it is
because there is no
> > "databind" command associated with the
control or page. Do you have a
> > "if not isPostBack then databind"
statement in the PageLoad event?
> >
> > -----Original Message-----
> > From: Bilal Haidar [MVP] [mailto:bhaidargmail.com]
> > Sent: Thursday, November 30, 2006 4:01 PM
> > To: aspnet-controlbuildingaspadvice.com
> > Subject: [aspnet-controlbuilding] Composite
Control
> >
> > Hello:
> >
> > I am developing a composite control, mover
control, where I have two
> > listboxes (xListBox) that I have developed and
published on
> > ASPAlliance.comwhere it saves any changes on the
client, my only issue
> > is that:
> >
> > I have exposed two public properties, one for the
Left Listbox and one
> > for
> > the right Listbox. Both properties are
"get" properties.
> >
> > If I bind data to those listboxes
programmatically, it works fine! If I
> > use
> > the Property window to add items to the Listboxes,
they are being added
> > on
> > the Designer view, but when the page runs, the
items are not shown.
> >
> > Any ideas in this?
> >
> > Regards
> >
> >
> >
> > Need SQL Advice? http://sqladvice.com
> > Need RegEx Advice? http://regexadvice.com
> > Need XML Advice? http://xmladvice.com
> >
> >
> >
> >
> > Need SQL Advice? http://sqladvice.com
> > Need RegEx Advice? http://regexadvice.com
> > Need XML Advice? http://xmladvice.com
> >
>
>
>
> Need SQL Advice? http://sqladvice.com
> Need RegEx Advice? http://regexadvice.com
> Need XML Advice? http://xmladvice.com
>
>
>
> Need SQL Advice? http://sqladvice.com
> Need RegEx Advice? http://regexadvice.com
> Need XML Advice? http://xmladvice.com
>
Need SQL Advice? http://sqladvice.com
Need RegEx Advice? http://regexadvice.com
Need XML Advice? http://xmladvice.com
|