Call for testers: TDM24XXP

	I finished the first version of tdm24xxp driver today.
It detects TDM800 card fine, though no audio/calls has been
tested
yet. If you have the hardware and time to try it - please,
grab
zaptel-1.4 branch from svn, or download the latest
snapshot:
http
://pbxpress.com/~gonzo/zaptel-bsd-1.4.tar.gz
and give it a try.

-- 
Sincerely,

Oleksandr Tymoshenko
PBXpress Communications, Inc.
http://www.pbxpress.com
Tel./Fax.: +1 866 SIP PBX1  Ext. 7117

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.c
om--

Asterisk-BSD mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-bsd

It detects TDM2400 and TE110p together:

Dec 24 13:20:39 iax kernel: Zapata Telephony Interface
Registered on 
major 196
Dec 24 13:20:39 iax kernel: Echo Canceller: MG2
Dec 24 13:20:39 iax kernel: T1/E1 device: vendor=e159
device=1 
subvendor=79fe
Dec 24 13:20:39 iax kernel: wcte11xp0: <Digium Wildcard
TE110P T1/E1 
Board> port 0x1000-0x10ff mem 0x52000000-0x52000fff irq
22 at device 1.0 
on pci7
Dec 24 13:20:39 iax kernel: WCT1xxP Attach for wcte11xp0:
deviceID : 0xe159
Dec 24 13:20:39 iax kernel: wcte11xp0: [FAST]
Dec 24 13:20:39 iax kernel: FALC version: 00000005
Dec 24 13:20:39 iax kernel: TE110P: Setting up global serial
parameters 
for E1 FALC V2.2
Dec 24 13:20:39 iax kernel: TE110P: Successfully initialized
serial bus 
for card
Dec 24 13:20:39 iax kernel: Found a Wildcard: Digium
Wildcard TE110P T1/E1
Dec 24 13:20:39 iax kernel: wctdm: TDM24XXP device:
vendor=d161 
device=2400 subvendor=d161
Dec 24 13:20:39 iax kernel: wctdm0: <Wildcard
TDM2400P> port 
0x1400-0x14ff mem 0x52001000-0x520013ff irq 21 at device 0.0
on pci7
Dec 24 13:20:39 iax kernel: wctdm0: [FAST]
Dec 24 13:20:39 iax kernel: PCI Config reg is 00000007
Dec 24 13:20:39 iax kernel: Wildcard TDM2400P: New Reg:
fe590000!
Dec 24 13:20:39 iax kernel: Detected REG0: 00000100
Dec 24 13:20:39 iax kernel: Detected REG1: 00007849
Dec 24 13:20:39 iax kernel: Detected REG2: 0000001d
Dec 24 13:20:39 iax kernel: (pre) Reg fc is 50000027
Dec 24 13:20:39 iax kernel: (post) Reg fc is 50000024
Dec 24 13:20:39 iax kernel: Detected REG2: 0000ffff
Dec 24 13:20:39 iax kernel: wctdm24xxp: reg is a04c0004
Dec 24 13:20:39 iax kernel: Resetting the modules...
Dec 24 13:20:39 iax kernel: During Resetting the modules...
Dec 24 13:20:39 iax kernel: After resetting the modules...

but many erros are reported on TDM2400:

Dec 24 13:20:39 iax kernel: Port 1: Not installed
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 1: 0 
volts (00) after 465 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 1 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2  iREG
25 = 0  
should be 8C
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 1: 0 
volts (00) after 189 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 1 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 300  
should be 320
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 2: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 2: 0 
volts (00) after 254 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 2 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= C0  should 
be 7C0
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 2: 0 
volts (00) after 5 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 2 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 20  
should be 320
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6  iREG
27 = 0  
should be 10
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 3: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 3: 0 
volts (00) after 93 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 3 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= C0  should 
be 7C0
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: Port 4: Installed -- MANUAL FXS
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 4: 0 
volts (00) after 248 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 4 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 4,
resetting!
Dec 24 13:20:39 iax kernel: Power alarm on module 4,
resetting!
Dec 24 13:20:39 iax kernel: Port 5: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 5: 0 
volts (00) after 94 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 5 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! OSC2_COEF  iREG 10 = 70 
should be 7870
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 300  
should be 320
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 5: 0 
volts (00) after 133 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 5 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: !!!!!!! RECV_DIGITAL_GAIN  iREG
1A = 0  
should be 2000
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 0  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 6: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 6: 0 
volts (00) after 49 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 6 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Port 7: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 7: 0 
volts (00) after 434 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 7 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 0  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 7: 0 
volts (00) after 172 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 7 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Port 8: Installed -- MANUAL FXS
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 8: 0 
volts (00) after 125 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 8 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: !!!!!!! RING_OSC  iREG 14 = F0 
should be 7EF0
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES  iREG 1C
= 1  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES  iREG 1D
= 8000  
should be 3600
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES  iREG 1E
= 0  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES  iREG 1F
= 0  should 
be 200
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= 1480  
should be 7C0
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4  iREG 21
= 37C0  
should be 4C00
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6  iREG 22
= 3D70  
should be 1B80
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 3970  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 78E0  
should be 320
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2  iREG
25 = 8B60  
should be 8C
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4  iREG
26 = 6A40  
should be 100
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6  iREG
27 = 8070  
should be 10
Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING  iREG 28
= FFFF  
should be C00
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V  iREG 29 =
FFFF  should 
be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA  iREG 2A =
FFFF  should be 
1000
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW 
iREG 2B = FFFF  
should be 1000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 8: 0 
volts (00) after 104 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 8 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES  iREG 1C
= 1  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES  iREG 1D
= 8000  
should be 3600
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES  iREG 1E
= 0  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES  iREG 1F
= 0  should 
be 200
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= 1480  
should be 7C0
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4  iREG 21
= 37C0  
should be 4C00
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6  iREG 22
= 3D70  
should be 1B80
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 3970  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 78E0  
should be 320
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2  iREG
25 = 8B60  
should be 8C
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4  iREG
26 = 6A40  
should be 100
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6  iREG
27 = 8070  
should be 10
Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING  iREG 28
= FF00  
should be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V  iREG 29 =
FFFF  should 
be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA  iREG 2A =
FFFF  should be 
1000
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW 
iREG 2B = FFFF  
should be 1000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 9: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 9: 0 
volts (00) after 228 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 9 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= C0  should 
be 7C0
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 9: 0 
volts (00) after 59 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 9 failed leakage
test.  Check 
for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 8,
resetting!
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: Too many power alarms on card 8,
NOT resetting!
Dec 24 13:20:39 iax kernel: !!!!!!! XMIT_DIGITAL_GAIN  iREG
1B = 0  
should be 4000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 10: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 10: 0 
volts (00) after 35 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 10 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! OSC2_COEF  iREG 10 = 70 
should be 7870
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES  iREG 1C
= 1  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES  iREG 1D
= 8000  
should be 3600
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES  iREG 1E
= 0  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES  iREG 1F
= 0  should 
be 200
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= 1480  
should be 7C0
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4  iREG 21
= 37C0  
should be 4C00
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6  iREG 22
= 3D70  
should be 1B80
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 3970  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 78E0  
should be 320
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2  iREG
25 = 8B60  
should be 8C
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4  iREG
26 = 6A40  
should be 100
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6  iREG
27 = 8070  
should be 10
Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING  iREG 28
= FFFF  
should be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V  iREG 29 =
FFFF  should 
be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA  iREG 2A =
FFFF  should be 
1000
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW 
iREG 2B = FFFF  
should be 1000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 10: 0 
volts (00) after 143 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 10 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Proslic Passed Manual
Calibration on Second 
Attempt
Dec 24 13:20:39 iax kernel: !!!!!!! DTMF_COL_2ND_ARM  iREG A
= 2  should 
be 202
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES  iREG 1C
= 1  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES  iREG 1D
= 8000  
should be 3600
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES  iREG 1E
= 0  should 
be 1000
Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES  iREG 1F
= 0  should 
be 200
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2  iREG 20
= 1480  
should be 7C0
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4  iREG 21
= 37C0  
should be 4C00
Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6  iREG 22
= 3D70  
should be 1B80
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER 
iREG 23 = 3970  
should be 8000
Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER  iREG
24 = 78E0  
should be 320
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2  iREG
25 = 8B60  
should be 8C
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4  iREG
26 = 6A40  
should be 100
Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6  iREG
27 = 8070  
should be 10
Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING  iREG 28
= FFFF  
should be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V  iREG 29 =
FFFF  should 
be C00
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA  iREG 2A =
FFFF  should be 
1000
Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW 
iREG 2B = FFFF  
should be 1000
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Port 11: FAILED FXS (FCC)
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 11: 0 
volts (00) after 244 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 11 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Port 12: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 12: 0 
volts (00) after 54 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 12 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Port 13: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 13: 0 
volts (00) after 409 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 13 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V  iREG 29 = 0 
should be C00
Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers
UNSUCCESSFULLY.
Dec 24 13:20:39 iax kernel: Indirect Registers failed
verification.
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 13: 0 
volts (00) after 268 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 13 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Port 14: Installed -- MANUAL
FXS
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 14: 0 
volts (00) after 119 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 14 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 15: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Excessive leakage detected on
module 15: 0 
volts (00) after 231 ms
Dec 24 13:20:39 iax kernel: ProSLIC module 15 failed leakage
test.  
Check for short circuit
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 16: Installed -- AUTO
FXS/DPO
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 17: Installed -- AUTO FXO
(FCC mode)
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 18: Installed -- AUTO FXO
(FCC mode)
Dec 24 13:20:39 iax kernel: Port 19: Installed -- AUTO FXO
(FCC mode)
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 20: Installed -- AUTO FXO
(FCC mode)
Dec 24 13:20:39 iax kernel: Port 21: Not installed
Dec 24 13:20:39 iax kernel: Port 22: Not installed
Dec 24 13:20:39 iax kernel: Port 23: Not installed
Dec 24 13:20:39 iax kernel: Power alarm on module 14,
resetting!
Dec 24 13:20:39 iax kernel: Port 24: Not installed
Dec 24 13:20:39 iax kernel: Found a Wildcard TDM: Wildcard
TDM2400P (24 
modules)

[rootiax /]# uname -a
FreeBSD iax.nlink.com.br 6.3-RC1 FreeBSD 6.3-RC1 #0: Tue Nov
27 00:59:35 
UTC 2007     rootdessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP 
i386

Paulo.

Oleksandr Tymoshenko escreveu, Em 30/10/2007 20:31:
> 	I finished the first version of tdm24xxp driver
today.
> It detects TDM800 card fine, though no audio/calls has
been tested
> yet. If you have the hardware and time to try it -
please, grab
> zaptel-1.4 branch from svn, or download the latest
snapshot:
> http
://pbxpress.com/~gonzo/zaptel-bsd-1.4.tar.gz
> and give it a try.
>
>   

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.c
om--

Asterisk-BSD mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-bsd