|
List Info
Thread: »Ø¸´£º Re: how can i edit the file to make calls!
|
|
| »Ø¸´£º Re: how can i edit the file to
make calls! |
 
China |
2008-01-09 23:12:13 |
|
hello, Richard:
I copied the file to /usr/locla/etc/asterisk and restarting asterisk. the LEDs are not activated. the capi show channesl:
*CLI> capi show channels
CAPI thread [0x0] {
Application ID : 0x00000000
Application uptime : 0x00000e2a seconds
Call descriptor statistics:
allocation count ; : 0x00000000 call descriptors
free count ; ; : 0x00000000 call descriptors
in memory count ; : 0x00000000 call descriptors
in use count ; : 0x00000000 call descriptors
record allocation rate : 0x0000
calls/second
limit allocation rate : 0x0010 calls/second
Currently active calls:
channel name, source->;destination, call ID, in/out
}
Config entry 'ISDN1' {
b_channels_curr : 2 call descriptor(s) free
;b_channels_max : 2 call descriptor(s) total
}
*CLI>
capi.conf
[ISDN1] ; ;this example interface gets name 'ISDN1' and may be any
; ; ;name not starting with 'g' or 'contr'.
isdnmode=msn ; ;'MSN' (point-to-multipoint)
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * == any
;
; Format of "incomingmsn" is like this:
;
; 0) This will only allow any MSN:
;
;
incomingmsn=*
;
; 1) This will only allow (MSN == "1"):
;
; incomingmsn=1
;
; 2) This will only allow (MSN == "1") or (MSN == "2") or (MSN == "3"):
;
; incomingmsn=1,2,3
;
; 3) This will only allow (MSN == "1XX..") or (MSN == "2") or (MSN == "3XX.."):
;
; incomingmsn=1*,2,3*
;
; NOTE: When a number matches "1*", everything preceeding the "*" is
; stripped away from the incoming number. For example if "incomingmsn=1*" and
; the MSN is 1234, only 234 is passed to Asterisk.
;
controller=1 ;ISDN4BSD default (first controller)
group=1 ; ;dialout group
;prefix=0 ; ;set a prefix to calling number on incoming calls
softdtmf=off ;enable/disable software dtmf detection
relaxdtmf=off ;in addition to softdtmf, you can
use
; ; ;relaxed dtmf detection, which implies softdtmf=yes
accountcode= ;Asterisk accountcode to use in CDRs
context=isdn_in ;context for incoming calls
holdtype=local ;when Asterisk puts the call on hold, ISDN HOLD will be used. If
; ; ;set to 'local' (default value), no hold is done and Asterisk may
; ; ;play MOH.
;immediate=yes ;immediate start of pbx with extension 's' if no digits were
; ; ;received on incoming call (no destination number yet)
echocancel=no ;disable echo canceller
echosquelch=no
;primitive echo suppression (in chan_capi)
;echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ; ;echo cancel tail setting
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;Asterisk call group
;deflect=1234567 ;deflect incoming calls to 1234567 if all B channels are busy
the dmesg shows:
i4bctl: ISDN system control port attached
capi: CAPI call control device attached, v2.10
i4b: ISDN call control device attached
i4btrc: 64 ISDN trace device(s) attached
i4brbch: 8 raw B channel access device(s) attached
i4btel: 8 ISDN telephony interface device(s) attached
i am not very sure the capi.conf for BRI 400P( 4 ports and in TE mode). how do i set TE modes for 4 ports? i just run: isdncinfig? or add some
parameters? below is what i run isdnconfig:
new-host-3# isdnconfig
controller 8 = {
Layer 1:
description : HFC-4S PCI ISDN adapter
type ; : passive ISDN (Basic Rate, 2xB)
; channels : 0x3
; serial : 0xabd5
power_save : on
dialtone & | |