CCM4.1 to GK to MCU...

I don't think the problem is with the zone subnet command. 
To restrict 
other subnets you will need to add this command:
zone subnet 10.1.1.1 default enable

 From what I can find the "rejectReason
discoveryRequired : NULL" means 
that the GK received a "lightweight" RRQ from the
GW (CCM) but needs to 
have a full registration message for the initial
registration.  In the 
RRQ that generated the RRJ is the KeepAlive field set to
True or False?

Kevin

On Oct 30, 2006, at 3:07 PM, Jonathan Charles wrote:

> I checked again, and that subnet has a /22 on it, so it
covers the 
> entire region...
>
> I ran the debugs and saw this:
>
>
> value RasMessage ::= registrationReject :
>     {
>       requestSeqNum 47
>       protocolIdentifier { 0 0 8 2250 0 4 }
>       rejectReason discoveryRequired : NULL
>     }
>
>
>
>
> Jonathan
>
> On 10/30/06, Ryan Ratliff < rratliffcisco.com> wrote:Check that zone 
> subnet command.  I'm pretty sure it restricts what IP
>> addresses the gatekeeper will allow registration
from.  Also check
>> out 'debug ras', 'debug h225 asn1', and 'debug
gatek main 10'.
>>
>> -Ryan
>>
>> On Oct 30, 2006, at 1:52 PM, Jonathan Charles
wrote:
>>
>> There is a route-pattern pointing to the trunk, but
the Gatekeeper
>> only shows the MCU registered as an endpoint.
>>
>> The CM is set to register as a gateway... and the
CM is not on the
>> same subnet...
>>
>>
>>
>> Jonathan
>>
>> On 10/30/06, Ryan Ratliff < rratliffcisco.com> wrote: You have to
>> have a route pattern pointing to the trunk for CM
to
>> register with the gk afaik.  Also note that CM only
retries
>> registration every 30-60 seconds.  For quicker
results reset the gk-
>> controlled trunk.  Also make sure you have CM set
to register as a
>> gateway not a terminal.
>>
>>  From your config I assume CM's IP address falls
within the
>> 10.1.1.0/22 subnet?
>>
>> -Ryan
>>
>> On Oct 30, 2006, at 12:38 PM, Jonathan Charles
wrote:
>>
>> OK, I have a CCM4.1 box, and I am trying to get it
to connect (for
>> video) to a Cisco MCU, via a gatekeeper...
>>
>> The MCU is registered to the gatekeeper as an
endpoint, but I can't
>> get the CCM to do the same...
>>
>> I have a gatekeeper controlled trunk pointing at
the MCU (with the GK
>> identified)...
>>
>> Still nothing...
>>
>> I also added a couple of route-patterns (with the
MCU service
>> prefixes) pointing at the trunk... Still nothing...
>>
>>
>> gatekeeper
>>    zone local 10.1.1.1 binky.com
>>    zone subnet 10.1.1.1  10.1.1.0/22 enable
>>    zone prefix 10.1.1.1 2125554244*
>>    gw-type-prefix 1#* default-technology
>>    no shutdown
>>
>>
>>
>> Any ideas?
>>
>>  TIA
>>
>>
>>
>> Jonathan
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voippuck.nether.net
>>  h
ttps://puck.nether.net/mailman/listinfo/cisco-voip
>>
> _______________________________________________
> cisco-voip mailing list
> cisco-voippuck.nether.net
> h
ttps://puck.nether.net/mailman/listinfo/cisco-voip
_______________________________________________
cisco-voip mailing list
cisco-voippuck.nether.net
h
ttps://puck.nether.net/mailman/listinfo/cisco-voip