how to test a t1 cas what are the cmds

If you're just trying to test phone calls over your
CAS T1, just like any other connection you can try to
use 'csim start <phonenumber>' to see if you can call
yourself.

Cisco recommends you don't use that command willynilly
since it has been known to crash the box so it is
probably best if you are physically located near it.

Paul

--- James Grace <jgraceadcapnet.com> wrote:

> ?
> how to test a t1 cas  what are the cmds
> Im trying to test some calls going over the t1 cas
> wink/start connection.  i not sure what cmds i can
> use
>  
> James Grace 
>  
> Systems Engineer
> Adcap Network Systems, Inc.
> 6865 Shiloh Road East, Suite 250
> Alpharetta, GA 30005
>  
> office: 678-456-6986
> direct: 678-456-6761
> jgraceadcapnet.com
> www.adcapnet.com <http://www.adcapnet.com/
> 
> Disclaimer For ADCAP Network Systems
> 
> "The information transmitted is intended only for
> the person or entity to which it is addressed and
> may
> contain confidential and/or privileged material. Any
> review, retransmission, dissemination or other use
> of,
> or taking of any action in reliance upon this
> information by persons or entities other than the
> intended
> recipient is prohibited. If you received this
> message in error, please contact the sender and
> delete the
> material from all computers."
> 
> This original email was sent to the internet for
> delivery at 25 May 2007 09:44:18 -0400
> > _______________________________________________
> cisco-voip mailing list
> cisco-voippuck.nether.net
> h
ttps://puck.nether.net/mailman/listinfo/cisco-voip
> 



 
____________________________________________________________
________________________
Food fight? Enjoy some healthy debate 
in the Yahoo! Answers Food & Drink Q&A.
http://answers.yahoo.com/dir/?link=list&sid=3965453
67
_______________________________________________
cisco-voip mailing list
cisco-voippuck.nether.net
h
ttps://puck.nether.net/mailman/listinfo/cisco-voip

to debug the e&m signaling:
debug vpm signal

to debug the call routing:
debug voice dialpeer

Regards Patrick

On 5/25/07, James Grace <jgraceadcapnet.com> wrote:
> ?
>
>
> how to test a t1 cas  what are the cmds
> Im trying to test some calls going over the t1 cas
wink/start connection.  i
> not sure what cmds i can use
>
>
>
> James Grace
>
> Systems Engineer
> Adcap Network Systems, Inc.
> 6865 Shiloh Road East, Suite 250
> Alpharetta, GA 30005
>
> office: 678-456-6986
> direct: 678-456-6761
> jgraceadcapnet.com
> www.adcapnet.comDisclaimer For ADCAP Network Systems
>
> "The information transmitted is intended only for
the person or entity to
> which it is addressed and may
> contain confidential and/or privileged material. Any
review, retransmission,
> dissemination or other use of,
> or taking of any action in reliance upon this
information by persons or
> entities other than the intended
> recipient is prohibited. If you received this message
in error, please
> contact the sender and delete the
> material from all computers."
>
> This original email was sent to the internet for
delivery at 25 May 2007
> 09:44:18 -0400
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voippuck.nether.net
> h
ttps://puck.nether.net/mailman/listinfo/cisco-voip
>
>
_______________________________________________
cisco-voip mailing list
cisco-voippuck.nether.net
h
ttps://puck.nether.net/mailman/listinfo/cisco-voip