I would agree with you and I have checked the feature set
through the
software
adviser. IP/FW/IDS Plus IPSEC 3DES basic is the feature
set. I'm running
64m
of ram with 16mb of flash. I could be 100% wrong - it seems
that way (GRIN)
Thanks for your input on this issue -
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version
12.2(15)T17, RELEASE
SOFTWARE
(fc1)
Technical Support: http://www.cisco.com
/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 12-Aug-05 15:49 by kehsiao
Image text-base: 0x80008098, data-base: 0x81942FEC
ROM: System Bootstrap, Version 11.3(2)XA3, PLATFORM SPECIFIC
RELEASE SOFTWARE
(fc1)
ROM: C2600 Software (C2600-IK9O3S3-M), Version 12.2(15)T17,
RELEASE SOFTWARE
(fc1)
uptime is 13 hours, 7 minutes
System returned to ROM by reload
System image file is
"flash:c2600-ik9o3s3-mz.122-15.T17.bin"
This product contains cryptographic features and is subject
to United
States and local country laws governing import, export,
transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use
encryption.
Importers, exporters, distributors and users are responsible
for
compliance with U.S. and local country laws. By using this
product you
agree to comply with applicable laws and regulations. If you
are unable
to comply with U.S. and local laws, return this product
immediately.
A summary of U.S. laws governing Cisco cryptographic
products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by
sending email to
export cisco.com.
cisco 2611 (MPC860) processor (revision 0x202) with
61440K/4096K bytes of
memory.
Processor board ID JAB02380027 (1765035008)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is
________________________________
From: Godswill Oletu [mailto:oletuinbox.lv]
Sent: Sun 4/30/2006 9:02 AM
To: Todd, Douglas M.; ciscogroupstudy.com
Subject: Re: OSPF V3 (IPV6 OSPF) on 2600 12.2.15T [7:109414]
Todd,
Are you sure you are running 12.2(15)T7 IP Plus on the 2600
or on a 2600XM
plateform? A 32 Meg flash is needed for that IOS version and
that will
require a BootRom upgrade on the 2600 plateform which
otherwise will only
take a maximum of 16 Meg flash.
It is very possible that you have Enterprise Basic IOS on
the 2600 and IP
Plus on the 2500 plateform. Enterprise Basic cannot run
OSPFv3 despite what
Cisco IOS Navigation says.
Posting the output of your 'show version' from the 2600
will clear this up.
HTH
Godswill Oletu
----- Original Message -----
From: "Todd, Douglas M."
To:
Sent: Sunday, April 30, 2006 6:52 AM
Subject: OSPF V3 (IPV6 OSPF) on 2600 12.2.15T [7:109414]
> Hey all.
>
> I am hoping someone has come across this already. I
have a 2600 running
> 12.2.15
> T7 which when you enter the command ipv6 router ospf 1
you don't change to
> rtr
> configuration mode. However, If I do the same commands
on a 2500 running
the
> same version of code it works fine. Both routers are
ip plus the 2600 is
> running crypto which seems to be the only real
difference. All that I have
> read
> states 12.2.15T is the line for ipv6 support (ripv6
works like a champ).
>
> Ideas?
>
> commands:
> 2600:
> labr2(config)#ipv6 unicast-routing
> labr2(config)#ipv6 router ospf 1
> labr2(config)#
> labr2(config)#
>
> 2500
> bb1(config)#ipv6 uni
> bb1(config)#ipv6 unicast-routing
> bb1(config)#ipv6 router os 1
> bb1(config-rtr)#
> clabc2bb1(config-rtr)#
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7
&i=109417&t=109414
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.
groupstudy.com/list/cisco.html
|