Project forrest (in module forrest) failed

To whom it may engage...
        
This is an automated request, but not an unsolicited one.
For 
more information please visit http://gump.apache
.org/nagged.html, 
and/or contact the folk at generalgump.apache.org.

Project forrest has an issue affecting its community
integration.
This issue affects 1 projects,
 and has been outstanding for 514 runs.
The current state of this project is 'Failed', with reason
'Configuration Failed'.
For reference only, the following projects are affected by
this:
    - forrest :  Apache Forrest is an XML standards-oriented
documentation fr...


Full details are available at:
    http://vmgump.apache.org/gump/public/forrest/forr
est/index.html

That said, some information snippets are provided here.

The following annotations (debug/informational/warning/error
messages) were provided:
 -INFO- Failed with reason configuration failed
 -ERROR- Bad Dependency. Project: cocoon unknown to *this*
workspace
 -INFO- Failed to extract fallback artifacts from Gump
Repository

To subscribe to this information via syndicated feeds:
- RSS: http://vmgump.apache.org/gump/public/forrest/forrest
/rss.xml
- Atom: http://vmgump.apache.org/gump/public/forrest/forres
t/atom.xml

============================== Gump Tracking Only ===
Produced by Gump version 2.2.
Gump Run 17000030112006,
vmgump.apache.org:vmgump-public:17000030112006
Gump E-mail Identifier (unique within run) #14.

--
Apache Gump
http://gump.apache.org/
[Instance: vmgump]

I finally got my 11/44 going and  in the process of getting
it to boot 
from the tu58 port. It does boot from the TA80 drives.

The switch options of coarse are many so I need to know what
its trying
to tell me.  If I do a " B  DD  it comes back with  
"console 177777707 sp
173416"   . the Tu58 software does see the machine
being turned off or on.
I have check the cabling (lines 2 and 3)  and most of the
switch positions.

thanks, Jerry

Jerry Wright
JLC inc

 

Jerry wrote:
> -----Original Message-----
> From: cctalk-bouncesclassiccmp.org 
> [mailto:cctalk-bouncesclassiccmp.org] On Behalf
Of g-wrightatt.net
> Sent: donderdag 30 november 2006 8:53
> To: cctalkclassiccmp.org
> Subject: Need Help With a 11/44
> 
> I finally got my 11/44 going and  in the process of
getting 
> it to boot from the tu58 port. It does boot from the
TA80 drives.
> 
> The switch options of coarse are many so I need to know
what 
> its trying to tell me.  If I do a " B  DD  it
comes back with
> "console 177777707 sp 173416".
> the Tu58 software does see the machine being turned off
or on.
> I have check the cabling (lines 2 and 3)  and most of
the 
> switch positions.
> 
> thanks, Jerry
> 
> Jerry Wright
> JLC inc


Hi Jerry,
I downloaded the 11/44 manuals from a bitsaver mirror site
to work
on my 11/44. In the process, I updated my webpages for the
/44 a lot.
Of course, nothing beats the manual, but I wrote the switch
settings
grouped together. The manual goes on describing the next
module, and
then shows a switch settings table that belongs to a
previously
discussed module. It was a bit confusing before I noticed
that ...
Regarding the message ... don't know, I haven't seen that
one.
It only tell you that the /44 is in console mode, shows the
address
of the stackpointer (and says so) and then the contents of
the SP.
Now ..., *when* it prints this message is perhaps described
in the
maintenance manual. I start guessing now. The contents of
the SP
seems to be an address in the boot PROM address range for
device #3
which should be in socket E50 ...
Look at the contents of the start addresses of the boot
PROMs to see
what's on the UBI (or pull the board and inspect visually).
If one of those boot PROMs is for a device that you have
(connected)
you can boot the /44 also with the simple start command, for
example
if you have 23-751A9 (RL) in socket E49, load a bootable
RL01 or RL02
pack in your drive and hit control-P on the console terminal
to get
the console prompt (>>>). Then enter "s
17773204" (& carriage return)
to boot from DL0: without executing CPU diagnostics. See my
UBI page.

I can boot my /44 now and it runs fine, but I have not yet
ran the
XXDP diags for the CPU ... If I stop RT-11, and use the
Start command
on the >>> prompt to boot RT-11 again, the system
hangs. However, if
I cycle power (UNLOAD the RL pack of course first!) and LOAD
the RL02
pack again, I can boot fine using the Start command ... huh?
 But, as
said, I haven't run XXDP!

- Henk.



This message and attachment(s) are intended solely for use
by the addressee and may contain information that is
privileged, confidential or otherwise exempt from disclosure
under applicable law.

If you are not the intended recipient or agent thereof
responsible for delivering this message to the intended
recipient, you are hereby notified that any dissemination,
distribution or copying of this communication is strictly
prohibited.

If you have received this communication in error, please
notify the sender immediately by telephone and with a
'reply' message.
  
Thank you for your co-operation.