On Fri, 25 Aug 2006, Matthew wrote:
> m. allan noah wrote:
>> i am sorry you are having problems. linux has a
learning curve
>> sometimes, and the fujitsu sane backend has JUST
been completely
>> re-written to support your scanner. if you wait a
few months for your
>> distro of choice to include sane 1.0.18, i bet 3/4
of these problems
>> will go away.
>
> I wish I could wait, but work has to go on and if I
can't get it done in
> Linux then it's back to Windows. I don't want to go
back to Windows.
>
ok, then we make this work.
>>
>> nothing personal, but you obviously dont know much
about linux (the fact
>> you reinstalled suse 3 times is a pretty good
indication of that), so
>> when you then jump off the beaten path and start
compiling your own
>> code, it is no wonder you cant make it work by
yourself.
>
> Your are right I am a Linux newbie. As far as jumping
off the beaten
> path... well, what choice do I have. Either I figure
out how to compile
> the source and make my scanner work (or find an RPM) or
I go back to
> Windows and wait.
did you try the suse unsupported sane 1.0.18 rpm? you should
be able to
install that instead of the source compile, if you cant make
the source
work. but no matter, you seem to have the source installed,
so lets stick
with that.
>
>>
>> dont feel like you have to founder on alone,
however. you have only sent
>> two previous mails to this list, and you got
answers to the questions
>> you asked. the same can be true for the rest of the
process.
>>
>> 1. the log below has no errors in it.
> If there are any other logs I can send let me know and
I will get them
> to you all.
>
ok. place a single sheet in the scanner. run, as root:
SANE_DEBUG_FUJITSU=15 scanimage (your options here)
2>take2.log >foo.pnm
that will attempt to scan, place the error/debug messages in
take2.log and
the image in foo.pnm
if there is an error in the log, send it. if not, repeat.
allan
--
"so don't tell us it can't be done, putting down
what you don't know.
money isn't our god, integrity will free our souls" -
Max Cavalera
--
sane-devel mailing list: sane-devel lists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|
m. allan noah wrote:
> On Fri, 25 Aug 2006, Matthew wrote:
>
>> m. allan noah wrote:
>>> i am sorry you are having problems. linux has a
learning curve
>>> sometimes, and the fujitsu sane backend has
JUST been completely
>>> re-written to support your scanner. if you wait
a few months for your
>>> distro of choice to include sane 1.0.18, i bet
3/4 of these problems
>>> will go away.
>>
>> I wish I could wait, but work has to go on and if I
can't get it done in
>> Linux then it's back to Windows. I don't want to
go back to Windows.
>>
>
> ok, then we make this work.
>
>>>
>>> nothing personal, but you obviously dont know
much about linux (the fact
>>> you reinstalled suse 3 times is a pretty good
indication of that), so
>>> when you then jump off the beaten path and
start compiling your own
>>> code, it is no wonder you cant make it work by
yourself.
>>
>> Your are right I am a Linux newbie. As far as
jumping off the beaten
>> path... well, what choice do I have. Either I
figure out how to compile
>> the source and make my scanner work (or find an
RPM) or I go back to
>> Windows and wait.
>
> did you try the suse unsupported sane 1.0.18 rpm? you
should be able to
> install that instead of the source compile, if you cant
make the source
> work. but no matter, you seem to have the source
installed, so lets
> stick with that.
>
>>
>>>
>>> dont feel like you have to founder on alone,
however. you have only sent
>>> two previous mails to this list, and you got
answers to the questions
>>> you asked. the same can be true for the rest of
the process.
>>>
>>> 1. the log below has no errors in it.
>> If there are any other logs I can send let me know
and I will get them
>> to you all.
>>
>
> ok. place a single sheet in the scanner. run, as root:
>
> SANE_DEBUG_FUJITSU=15 scanimage (your options here)
2>take2.log >foo.pnm
>
> that will attempt to scan, place the error/debug
messages in take2.log
> and the image in foo.pnm
>
> if there is an error in the log, send it. if not,
repeat.
>
> allan
>
I did use the unsupported sane RPM from the 10.1 directory
on the ftp site.
** Error log **
[sanei_debug] Setting debug level of fujitsu to 15.
[fujitsu] sane_init: start
[fujitsu] sane_init: fujitsu backend 1.0.33, from
sane-backends 1.0.18
[fujitsu] sane_init: finish
[fujitsu] sane_get_devices: start
[fujitsu] find_scanners: start
[fujitsu] find_scanners: reading config file fujitsu.conf
[fujitsu] find_scanners: setting "buffer-size"
to 65536
[fujitsu] find_scanners: looking for 'scsi FUJITSU'
[fujitsu] find_scanners: looking for 'usb 0x04c5 0x10e0'
[fujitsu] attach_one: start
[fujitsu] attach_one: looking for 'libusb:001:005'
[fujitsu] connect_fd: start
[fujitsu] connect_fd: opening USB device
[fujitsu] wait_scanner: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] wait_scanner: finish
[fujitsu] connect_fd: finish
[fujitsu] init_inquire: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] init_inquire: Found FUJITSU scanner fi-5120Cdj
version 0C00 at
libusb:001:005
[fujitsu] inquiry options
[fujitsu] color offset: 0 lines
[fujitsu] duplex offset: 0 lines
[fujitsu] init_inquire: finish
[fujitsu] init_vpd: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] standard options
[fujitsu] basic x res: 600 dpi
[fujitsu] basic y res: 600 dpi
[fujitsu] step x res: 1 dpi
[fujitsu] step y res: 1 dpi
[fujitsu] max x res: 600 dpi
[fujitsu] max y res: 600 dpi
[fujitsu] min x res: 50 dpi
[fujitsu] min y res: 50 dpi
[fujitsu] 60 dpi: 1
[fujitsu] 75 dpi: 1
[fujitsu] 100 dpi: 1
[fujitsu] 120 dpi: 1
[fujitsu] 150 dpi: 1
[fujitsu] 160 dpi: 1
[fujitsu] 180 dpi: 1
[fujitsu] 200 dpi: 1
[fujitsu] 240 dpi: 1
[fujitsu] 300 dpi: 1
[fujitsu] 320 dpi: 1
[fujitsu] 400 dpi: 1
[fujitsu] 480 dpi: 1
[fujitsu] 600 dpi: 1
[fujitsu] 800 dpi: 0
[fujitsu] 1200 dpi: 0
[fujitsu] max width: 8.85 inches
[fujitsu] max length: 34.00 inches
[fujitsu] overflow: 1
[fujitsu] monochrome: 1
[fujitsu] halftone: 1
[fujitsu] grayscale: 1
[fujitsu] color_monochrome: 0
[fujitsu] color_halftone: 0
[fujitsu] color_grayscale: 1
[fujitsu] vendor options
[fujitsu] operator panel: 1
[fujitsu] barcode: 0
[fujitsu] imprinter: 0
[fujitsu] duplex: 1
[fujitsu] transparency: 0
[fujitsu] flatbed: 0
[fujitsu] adf: 1
[fujitsu] A/D bits: 10
[fujitsu] buffer bytes: 16777216
[fujitsu] subwindow cmd: 0
[fujitsu] endorser cmd: 0
[fujitsu] hardware status cmd: 1
[fujitsu] scanner control cmd: 1
[fujitsu] brightness steps: 0
[fujitsu] threshold steps: 255
[fujitsu] contrast steps: 0
[fujitsu] built in gamma patterns: 0
[fujitsu] download gamma patterns: 1
[fujitsu] built in dither patterns: 4
[fujitsu] download dither patterns: 1
[fujitsu] black and white rif: 1
[fujitsu] automatic binary DTC: 0
[fujitsu] simplified DTC: 1
[fujitsu] outline extraction: 0
[fujitsu] image emphasis: 1
[fujitsu] automatic separation: 0
[fujitsu] mirror image: 0
[fujitsu] white level follower: 0
[fujitsu] subwindow: 0
[fujitsu] compression MH: 0
[fujitsu] compression MR: 0
[fujitsu] compression MMR: 0
[fujitsu] compression JBIG: 0
[fujitsu] compression JPG1: 1
[fujitsu] compression JPG2: 0
[fujitsu] compression JPG3: 0
[fujitsu] init_vpd: finish
[fujitsu] init_model: start
[fujitsu] init_model: finish
[fujitsu] init_options: start
[fujitsu] init_options: finish
[fujitsu] disconnect_fd: start
[fujitsu] disconnecting usb device
[fujitsu] disconnect_fd: finish
[fujitsu] attach_one: finish
[fujitsu] find_scanners: found scanner libusb:001:005
[fujitsu] find_scanners: found 1 scanner(s)
[fujitsu] find_scanners: finish
[fujitsu] sane_get_devices: finish
[fujitsu] sane_open: start
[fujitsu] sane_open: searching currently attached scanners
[fujitsu] sane_open: device libusb:001:005 requested
[fujitsu] sane_open: device libusb:001:005 found
[fujitsu] connect_fd: start
[fujitsu] connect_fd: opening USB device
[fujitsu] wait_scanner: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] wait_scanner: finish
[fujitsu] connect_fd: finish
[fujitsu] sane_open: finish
[fujitsu] sane_start: start
[fujitsu] started=0, img_count=0, source=1
[fujitsu] scanner_control: start
[fujitsu] scanner_control: power up lamp...
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] scanner_control: lamp on, tries 1, ret 0
[fujitsu] scanner_control: finish
[fujitsu] calculateDerivedValues: start
[fujitsu] xres=600, tlx=0, brx=10200, pw=10200, maxx=10624
[fujitsu] yres=600, tly=0, bry=13200, ph=13200, maxy=40800
[fujitsu] xres=600, tlx=0, brx=10208, pw=10200, maxx=10624
[fujitsu] yres=600, tly=0, bry=13200, ph=13200, maxy=40800
[fujitsu] calculateDerivedValues: finish
[fujitsu] setup_buffers: start
[fujitsu] setup_buffers: finish
[fujitsu] set_window: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] set_window: finish
[fujitsu] object_position: start
[fujitsu] object_position: load
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] wait_scanner: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] wait_scanner: finish
[fujitsu] object_position: finish
[fujitsu] start_scan: start
[fujitsu] do_usb_cmd: start
[fujitsu] do_usb_cmd: finish
[fujitsu] start_scan: finish
[fujitsu] started=1, img_count=0, source=1
[fujitsu] sane_start: finish
[fujitsu] sane_get_parameters: start
[fujitsu] calculateDerivedValues: start
[fujitsu] xres=600, tlx=0, brx=10208, pw=10200, maxx=10624
[fujitsu] yres=600, tly=0, bry=13200, ph=13200, maxy=40800
[fujitsu] xres=600, tlx=0, brx=10208, pw=10200, maxx=10624
[fujitsu] yres=600, tly=0, bry=13200, ph=13200, maxy=40800
[fujitsu] calculateDerivedValues: finish
[fujitsu] depth 1
[fujitsu] lines 6600
[fujitsu] pixels_per_line 5104
[fujitsu] bytes_per_line 638
[fujitsu] sane_get_parameters: finish
scanimage: scanning image of size 5104x6600 pixels at 1
bits/pixel
scanimage: acquiring gray frame
[fujitsu] sane_read: start
[fujitsu] read_from_scanner: start
[fujitsu] read_from_scanner: si:0 to:4210800 rx:0 re:4210800
bu:65536
pa:65076
[fujitsu] do_usb_cmd: start
[fujitsu] in: return error 'End of file reached'
[fujitsu] read_from_scanner: got EOF, changing to GOOD
[fujitsu] copy_buffer: start
[fujitsu] copy_buffer: finish
[fujitsu] read_from_scanner: finish
[fujitsu] read_from_buffer: start
[fujitsu] read_from_buffer: si:0 to:4210800 tx:0 re:65076
bu:32768 pa:32768
[fujitsu] read_from_buffer: finish
[fujitsu] sane_read: finish
[fujitsu] sane_read: start
[fujitsu] read_from_scanner: start
[fujitsu] read_from_scanner: si:0 to:4210800 rx:65076
re:4145724
bu:65536 pa:65076
[fujitsu] do_usb_cmd: start
[fujitsu] cmd: return error 'Error during device I/O'
[fujitsu] read_from_scanner: error reading data block status
= 9
[fujitsu] read_from_scanner: finish
[fujitsu] sane_read: front returning 9
scanimage: sane_read: Error during device I/O
[fujitsu] sane_cancel: start
[fujitsu] do_cancel: start
[fujitsu] do_cancel: finish
[fujitsu] sane_cancel: finish
[fujitsu] sane_close: start
[fujitsu] do_cancel: start
[fujitsu] do_cancel: finish
[fujitsu] disconnect_fd: start
[fujitsu] disconnecting usb device
[fujitsu] disconnect_fd: finish
[fujitsu] sane_close: finish
[fujitsu] sane_exit: start
[fujitsu] disconnect_fd: start
[fujitsu] disconnect_fd: finish
[fujitsu] sane_exit: finish
** end **
--
sane-devel mailing list: sane-devellists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|