|
List Info
Thread: CanoScan LiDE 30 on NetBSD not found
|
|
| CanoScan LiDE 30 on NetBSD not found |
|
2006-11-09 18:47:37 |
Hi,
sane-find-scanner can find the scanner on /dev/uscanner0,
but don't know
the manufactor and the model. output of sane-find-scanner is
----------------
found USB scanner (UNKNOWN vendor and product) at device
/dev/uscanner0
---------------
output of "scanimage -L" is
----------------------------
No scanners were identified. If you were expecting something
different,
check that the scanner is plugged in, turned on and detected
by the
sane-find-scanner tool (if appropriate). Please read the
documentation
which came with this software (README, FAQ, manpages).
--------------------------
I tried to configure the backend 'plustek.conf' to provide
vender ID and
product ID. But scanimage is still not working.
"scanimage -L" just hangs
there and no output.
After setting the DEBUG environmental variable, the
'scanimage -L' outputs
a message of 'waiting for scanner-ready' and stucks there.
Could you please help?
Thanks,
Xihong
--
sane-devel mailing list: sane-devel lists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|
|
| CanoScan LiDE 30 on NetBSD not found |
|
2006-11-10 06:20:22 |
On Thursday 09 November 2006 19:47, Xihong Yin wrote:
> Hi,
>
> sane-find-scanner can find the scanner on
/dev/uscanner0, but don't know
> the manufactor and the model. output of
sane-find-scanner is
>
> ----------------
> found USB scanner (UNKNOWN vendor and product) at
device /dev/uscanner0
> ---------------
>
> output of "scanimage -L" is
> ----------------------------
> No scanners were identified. If you were expecting
something different,
> check that the scanner is plugged in, turned on and
detected by the
> sane-find-scanner tool (if appropriate). Please read
the documentation
> which came with this software (README, FAQ, manpages).
> --------------------------
>
> I tried to configure the backend 'plustek.conf' to
provide vender ID and
> product ID. But scanimage is still not working.
"scanimage -L" just hangs
> there and no output.
>
> After setting the DEBUG environmental variable, the
'scanimage -L' outputs
> a message of 'waiting for scanner-ready' and stucks
there.
>
Hi,
I suspect a problem in the underlying USB-subsystem.
Could you please post the output of
SANE_DEBUG_PLUSTEK=19
- Gerhard
--
sane-devel mailing list: sane-devellists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|
|
| CanoScan LiDE 30 on NetBSD not found |
|
2006-11-10 13:52:14 |
Hi Gerhard,
Thank you for your reply. Here is the output:
[sanei_debug] Setting debug level of plustek to 19.
[plustek] Plustek backend V0.51-12, part of sane-backends
1.0.18
[plustek] Retrieving all supported and conntected devices
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0016
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0007
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x0005
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0012
[plustek] Checking for 0x0400-0x1000
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0458-0x2007
[plustek] Checking for 0x0458-0x2008
[plustek] Checking for 0x0458-0x2009
[plustek] Checking for 0x0458-0x2013
[plustek] Checking for 0x0458-0x2015
[plustek] Checking for 0x0458-0x2016
[plustek] Checking for 0x03f0-0x0505
[plustek] Checking for 0x03f0-0x0605
[plustek] Checking for 0x04b8-0x010f
[plustek] Checking for 0x04b8-0x011d
[plustek] Checking for 0x1606-0x0050
[plustek] Checking for 0x1606-0x0060
[plustek] Checking for 0x1606-0x0160
[plustek] Checking for 0x049f-0x001a
[plustek] Checking for 0x04a9-0x2206
[plustek] Checking for 0x04a9-0x2207
[plustek] Checking for 0x04a9-0x2208
[plustek] Checking for 0x04a9-0x220d
[plustek] Checking for 0x04a9-0x220e
[plustek] Checking for 0x04a9-0x2220
[plustek] Checking for 0x0a82-0x6620
[plustek] Available and supported devices:
[plustek] NONE.
[plustek] ># Plustek-SANE Backend configuration file<
[plustek] ># For use with LM9831/2/3 based USB
scanners<
[plustek] >#<
[plustek] ><
[plustek] ># each device needs at least two lines:<
[plustek] ># - [usb] vendor-ID and product-ID<
[plustek] ># - device devicename<
[plustek] ># i.e. for Plustek (0x07B3) UT12/16/24
(0x0017)<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device /dev/usbscanner<
[plustek] ># or<
[plustek] ># device libusb:bbb:ddd<
[plustek] ># where bbb is the busnumber and ddd the
device number<
[plustek] ># make sure that your user has access to
/proc/bus/usb/bbb/ddd<
[plustek] >#<
[plustek] ># additionally you can specify some
options<
[plustek] ># warmup, lOffOnEnd, lampOff<
[plustek] >#<
[plustek] ># For autodetection use<
[plustek] >#[usb]<
[plustek] ># device /dev/usbscanner<
[plustek] >[usb] 0x04A9 0x220E<
[plustek] next device is a USB device (0x04A9-0x220E)
[plustek] ... next device
[plustek] >device /dev/uscanner0<
[plustek] Decoding device name >/dev/uscanner0<
[plustek] >#device auto<
[plustek] ><
[plustek] attach (/dev/uscanner0, 0xbfbfddb0, 0x0)
[plustek] Device configuration:
[plustek] device name : >/dev/uscanner0<
[plustek] USB-ID : >0x04A9-0x220E<
[plustek] model ovr. : 0
[plustek] warmup : -1s
[plustek] lampOff : -1
[plustek] lampOffOnEnd : yes
[plustek] cacheCalData : no
[plustek] altCalibrate : no
[plustek] skipCalibr. : no
[plustek] skipFine : no
[plustek] skipFineWhite: no
[plustek] invertNegs. : no
[plustek] dis.Speedup : no
[plustek] pos_x : 0
[plustek] pos_y : 0
[plustek] pos_shading_y: -1
[plustek] neg_x : 0
[plustek] neg_y : 0
[plustek] neg_shading_y: -1
[plustek] tpa_x : 0
[plustek] tpa_y : 0
[plustek] tpa_shading_y: -1
[plustek] red gain : -1
[plustek] green gain : -1
[plustek] blue gain : -1
[plustek] red offset : -1
[plustek] green offset : -1
[plustek] blue offset : -1
[plustek] red lampoff : -1
[plustek] green lampoff: -1
[plustek] blue lampoff : -1
[plustek] red Gamma : 1.00
[plustek] green Gamma : 1.00
[plustek] blue Gamma : 1.00
[plustek] gray Gamma : 1.00
[plustek] ---------------------
[plustek] usbDev_open(/dev/uscanner0,0x04A9-0x220E) - 0x0
[plustek] Can't get vendor & product ID from driver...
[plustek] ... using the specified: 0x04A9-0x220E
[plustek] usbio_DetectLM983x
[plustek] usbio_DetectLM983x: found LM9832/3
[plustek] * setting device to idle state!
[plustek] Detected vendor & product ID: 0x04A9-0x220E
[plustek] Device description for >0x04A9-0x220E<
found.
[plustek] usb_initDev(42,0x04a9,-1)
[plustek] Device WAF : 0x00000002
[plustek] Transferrate: 1000000 Bytes/s
[plustek] Device Flags: 0x00000000
[plustek] Vendor adjusted to: >Canon<
[plustek] LAMP-STATUS: 0x00000000
[plustek] RESETTING REGISTERS(-1) - 0x80
[plustek] SETTING THE MISC I/Os
[plustek] MISC I/O after RESET: 0x66, 0x16, 0x91
[plustek] Calibration file-names set to:
[plustek]
>/home/c512/.sane/Canon-N1240U_LiDE30-coarse.cal<
[plustek]
>/home/c512/.sane/Canon-N1240U_LiDE30-fine.cal<
[plustek] usb_SetScanParameters()
[plustek] * HDPI: 8.000
[plustek] * XDPI=150, HDPI=8.000
[plustek] * YDPI=150, MinDPIY=75
[plustek] * DataPixelStart=52, LineEnd=52
[plustek] >> End-Start=0, HDPI=8.00
[plustek] * Full Steps to Skip at Start = 0x0000
[plustek] * StepSize(Preset) = 144 (0x0090)
[plustek] * Scan calculations...
[plustek] * LineLength=10592, LineRateColor=3
[plustek] * Stepsize = 996, 0x46=0x03 0x47=0xe4
[plustek] * DPD =960 (0x03c0)
[plustek] * DPD =30816 (0x7860), step size=996, steps2rev=32
[plustek] * llen=10592, lineRateColor=3, qtcnt=8, hfcnt=8
[plustek] usb_GetMCLKDivider()
[plustek] usb_GetMCLKDiv()
[plustek] - lower mclkdiv limit=2.500000
[plustek] - upper mclkdiv limit=32.500000
[plustek] - hdpi = 8.000
[plustek] - pixelbits = 8
[plustek] - pixelsperline = 0
[plustek] - linelen = 10592
[plustek] - transferrate = 1000000
[plustek] - MCLK Divider = 0
[plustek] - Current MCLK Divider = 2
[plustek] * Integration Time Adjust = 0
(HDPI=8.000,MCLKD=4.000)
[plustek] * Setting GreenPWMDutyCycleHigh
[plustek] * Current MCLK Divider = 4.000000
[plustek] * MOTOR-Settings: PWM=0x08, PWM_DUTY=0x1f
[plustek] * FFStepSize = 347, [0x48] = 0x01, [0x49] = 0x5b
[plustek] * PhyBytes = 6
[plustek] * PhyLines = 4
[plustek] * TotalBytes = 24
[plustek] * PL=295, coeffsize=216, scaler=3
[plustek] * PauseLimit = 2, [0x4e] = 0x01, [0x4f] = 0x01
[plustek] * Scansteps=72 (9*1200/150)
[plustek] usb_SetScanParameters() done.
[plustek] usbDev_getCaps()
[plustek] Scanner information:
[plustek] Vendor : Canon
[plustek] Model : N1240U/LiDE30
[plustek] Flags : 0x00000000
[plustek] drvclose()
[plustek] usbDev_stopScan()
[plustek] usbDev_ScanEnd(), start=0, park=0
[plustek] usbDev_close()
[plustek] attach: model = >N1240U/LiDE30<
[plustek] sane_get_devices (0xbfbfe6d8, 0)
device `plustek:/dev/uscanner0' is a Canon N1240U/LiDE30 USB
flatbed
scanner
[plustek] sane_exit
[plustek] Shutdown called (dev->fd=-1, /dev/uscanner0)
[plustek] Waiting for scanner-ready...
Thanks,
Xihong
On Fri, 10 Nov 2006, Gerhard Jaeger wrote:
> On Thursday 09 November 2006 19:47, Xihong Yin wrote:
> > Hi,
> >
> > sane-find-scanner can find the scanner on
/dev/uscanner0, but don't know
> > the manufactor and the model. output of
sane-find-scanner is
> >
> > ----------------
> > found USB scanner (UNKNOWN vendor and product) at
device /dev/uscanner0
> > ---------------
> >
> > output of "scanimage -L" is
> > ----------------------------
> > No scanners were identified. If you were expecting
something different,
> > check that the scanner is plugged in, turned on
and detected by the
> > sane-find-scanner tool (if appropriate). Please
read the documentation
> > which came with this software (README, FAQ,
manpages).
> > --------------------------
> >
> > I tried to configure the backend 'plustek.conf' to
provide vender ID and
> > product ID. But scanimage is still not working.
"scanimage -L" just hangs
> > there and no output.
> >
> > After setting the DEBUG environmental variable,
the 'scanimage -L' outputs
> > a message of 'waiting for scanner-ready' and
stucks there.
> >
> Hi,
>
> I suspect a problem in the underlying USB-subsystem.
> Could you please post the output of
> SANE_DEBUG_PLUSTEK=19
>
> - Gerhard
>
>
> --
> sane-devel mailing list: sane-devellists.alioth.debian.org
> http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
> Unsubscribe: Send mail with subject "unsubscribe
your_password"
> to sane-devel-requestlists.alioth.debian.org
>
--
sane-devel mailing list: sane-devellists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|
|
| CanoScan LiDE 30 on NetBSD not found |
|
2006-11-11 15:39:35 |
Hello!
For the record, I have to disable the uscanner devices to
access my USB
scanner on NetBSD (3.0). At the bootprompt I enter
boot -c
and disable the USB scanners via
disable uscanner
quit
Now this will prevent the kernel from taking over the
control of the
scanner. Only then libusb can see the scanner in my case.
Then
everything works as expected.
Best regards, Martin Bock
On Fri, Nov 10, 2006 at 08:52:14AM -0500, Xihong Yin wrote:
> Hi Gerhard,
>
> Thank you for your reply. Here is the output:
>
> [sanei_debug] Setting debug level of plustek to 19.
> [plustek] Plustek backend V0.51-12, part of
sane-backends 1.0.18
> [plustek] Retrieving all supported and conntected
devices
> [plustek] Checking for 0x07b3-0x0010
> [plustek] Checking for 0x07b3-0x0011
> [plustek] Checking for 0x07b3-0x0017
> [plustek] Checking for 0x07b3-0x0015
> [plustek] Checking for 0x07b3-0x0017
> [plustek] Checking for 0x07b3-0x0013
> [plustek] Checking for 0x07b3-0x0013
> [plustek] Checking for 0x07b3-0x0011
> [plustek] Checking for 0x07b3-0x0010
> [plustek] Checking for 0x07b3-0x0014
> [plustek] Checking for 0x07b3-0x0015
> [plustek] Checking for 0x07b3-0x0014
> [plustek] Checking for 0x07b3-0x0016
> [plustek] Checking for 0x07b3-0x0017
> [plustek] Checking for 0x07b3-0x0017
> [plustek] Checking for 0x07b3-0x0007
> [plustek] Checking for 0x07b3-0x000f
> [plustek] Checking for 0x07b3-0x000f
> [plustek] Checking for 0x07b3-0x0005
> [plustek] Checking for 0x07b3-0x0014
> [plustek] Checking for 0x07b3-0x0012
> [plustek] Checking for 0x0400-0x1000
> [plustek] Checking for 0x0400-0x1001
> [plustek] Checking for 0x0400-0x1001
> [plustek] Checking for 0x0458-0x2007
> [plustek] Checking for 0x0458-0x2008
> [plustek] Checking for 0x0458-0x2009
> [plustek] Checking for 0x0458-0x2013
> [plustek] Checking for 0x0458-0x2015
> [plustek] Checking for 0x0458-0x2016
> [plustek] Checking for 0x03f0-0x0505
> [plustek] Checking for 0x03f0-0x0605
> [plustek] Checking for 0x04b8-0x010f
> [plustek] Checking for 0x04b8-0x011d
> [plustek] Checking for 0x1606-0x0050
> [plustek] Checking for 0x1606-0x0060
> [plustek] Checking for 0x1606-0x0160
> [plustek] Checking for 0x049f-0x001a
> [plustek] Checking for 0x04a9-0x2206
> [plustek] Checking for 0x04a9-0x2207
> [plustek] Checking for 0x04a9-0x2208
> [plustek] Checking for 0x04a9-0x220d
> [plustek] Checking for 0x04a9-0x220e
> [plustek] Checking for 0x04a9-0x2220
> [plustek] Checking for 0x0a82-0x6620
> [plustek] Available and supported devices:
> [plustek] NONE.
> [plustek] ># Plustek-SANE Backend configuration
file<
> [plustek] ># For use with LM9831/2/3 based USB
scanners<
> [plustek] >#<
> [plustek] ><
> [plustek] ># each device needs at least two
lines:<
> [plustek] ># - [usb] vendor-ID and product-ID<
> [plustek] ># - device devicename<
> [plustek] ># i.e. for Plustek (0x07B3) UT12/16/24
(0x0017)<
> [plustek] ># [usb] 0x07B3 0x0017<
> [plustek] ># device /dev/usbscanner<
> [plustek] ># or<
> [plustek] ># device libusb:bbb:ddd<
> [plustek] ># where bbb is the busnumber and ddd the
device number<
> [plustek] ># make sure that your user has access to
/proc/bus/usb/bbb/ddd<
> [plustek] >#<
> [plustek] ># additionally you can specify some
options<
> [plustek] ># warmup, lOffOnEnd, lampOff<
> [plustek] >#<
> [plustek] ># For autodetection use<
> [plustek] >#[usb]<
> [plustek] ># device /dev/usbscanner<
> [plustek] >[usb] 0x04A9 0x220E<
> [plustek] next device is a USB device (0x04A9-0x220E)
> [plustek] ... next device
> [plustek] >device /dev/uscanner0<
> [plustek] Decoding device name >/dev/uscanner0<
> [plustek] >#device auto<
> [plustek] ><
> [plustek] attach (/dev/uscanner0, 0xbfbfddb0, 0x0)
> [plustek] Device configuration:
> [plustek] device name : >/dev/uscanner0<
> [plustek] USB-ID : >0x04A9-0x220E<
> [plustek] model ovr. : 0
> [plustek] warmup : -1s
> [plustek] lampOff : -1
> [plustek] lampOffOnEnd : yes
> [plustek] cacheCalData : no
> [plustek] altCalibrate : no
> [plustek] skipCalibr. : no
> [plustek] skipFine : no
> [plustek] skipFineWhite: no
> [plustek] invertNegs. : no
> [plustek] dis.Speedup : no
> [plustek] pos_x : 0
> [plustek] pos_y : 0
> [plustek] pos_shading_y: -1
> [plustek] neg_x : 0
> [plustek] neg_y : 0
> [plustek] neg_shading_y: -1
> [plustek] tpa_x : 0
> [plustek] tpa_y : 0
> [plustek] tpa_shading_y: -1
> [plustek] red gain : -1
> [plustek] green gain : -1
> [plustek] blue gain : -1
> [plustek] red offset : -1
> [plustek] green offset : -1
> [plustek] blue offset : -1
> [plustek] red lampoff : -1
> [plustek] green lampoff: -1
> [plustek] blue lampoff : -1
> [plustek] red Gamma : 1.00
> [plustek] green Gamma : 1.00
> [plustek] blue Gamma : 1.00
> [plustek] gray Gamma : 1.00
> [plustek] ---------------------
> [plustek] usbDev_open(/dev/uscanner0,0x04A9-0x220E) -
0x0
> [plustek] Can't get vendor & product ID from
driver...
> [plustek] ... using the specified: 0x04A9-0x220E
> [plustek] usbio_DetectLM983x
> [plustek] usbio_DetectLM983x: found LM9832/3
> [plustek] * setting device to idle state!
> [plustek] Detected vendor & product ID:
0x04A9-0x220E
> [plustek] Device description for >0x04A9-0x220E<
found.
> [plustek] usb_initDev(42,0x04a9,-1)
> [plustek] Device WAF : 0x00000002
> [plustek] Transferrate: 1000000 Bytes/s
> [plustek] Device Flags: 0x00000000
> [plustek] Vendor adjusted to: >Canon<
> [plustek] LAMP-STATUS: 0x00000000
> [plustek] RESETTING REGISTERS(-1) - 0x80
> [plustek] SETTING THE MISC I/Os
> [plustek] MISC I/O after RESET: 0x66, 0x16, 0x91
> [plustek] Calibration file-names set to:
> [plustek]
>/home/c512/.sane/Canon-N1240U_LiDE30-coarse.cal<
> [plustek]
>/home/c512/.sane/Canon-N1240U_LiDE30-fine.cal<
> [plustek] usb_SetScanParameters()
> [plustek] * HDPI: 8.000
> [plustek] * XDPI=150, HDPI=8.000
> [plustek] * YDPI=150, MinDPIY=75
> [plustek] * DataPixelStart=52, LineEnd=52
> [plustek] >> End-Start=0, HDPI=8.00
> [plustek] * Full Steps to Skip at Start = 0x0000
> [plustek] * StepSize(Preset) = 144 (0x0090)
> [plustek] * Scan calculations...
> [plustek] * LineLength=10592, LineRateColor=3
> [plustek] * Stepsize = 996, 0x46=0x03 0x47=0xe4
> [plustek] * DPD =960 (0x03c0)
> [plustek] * DPD =30816 (0x7860), step size=996,
steps2rev=32
> [plustek] * llen=10592, lineRateColor=3, qtcnt=8,
hfcnt=8
> [plustek] usb_GetMCLKDivider()
> [plustek] usb_GetMCLKDiv()
> [plustek] - lower mclkdiv limit=2.500000
> [plustek] - upper mclkdiv limit=32.500000
> [plustek] - hdpi = 8.000
> [plustek] - pixelbits = 8
> [plustek] - pixelsperline = 0
> [plustek] - linelen = 10592
> [plustek] - transferrate = 1000000
> [plustek] - MCLK Divider = 0
> [plustek] - Current MCLK Divider = 2
> [plustek] * Integration Time Adjust = 0
(HDPI=8.000,MCLKD=4.000)
> [plustek] * Setting GreenPWMDutyCycleHigh
> [plustek] * Current MCLK Divider = 4.000000
> [plustek] * MOTOR-Settings: PWM=0x08, PWM_DUTY=0x1f
> [plustek] * FFStepSize = 347, [0x48] = 0x01, [0x49] =
0x5b
> [plustek] * PhyBytes = 6
> [plustek] * PhyLines = 4
> [plustek] * TotalBytes = 24
> [plustek] * PL=295, coeffsize=216, scaler=3
> [plustek] * PauseLimit = 2, [0x4e] = 0x01, [0x4f] =
0x01
> [plustek] * Scansteps=72 (9*1200/150)
> [plustek] usb_SetScanParameters() done.
> [plustek] usbDev_getCaps()
> [plustek] Scanner information:
> [plustek] Vendor : Canon
> [plustek] Model : N1240U/LiDE30
> [plustek] Flags : 0x00000000
> [plustek] drvclose()
> [plustek] usbDev_stopScan()
> [plustek] usbDev_ScanEnd(), start=0, park=0
> [plustek] usbDev_close()
> [plustek] attach: model = >N1240U/LiDE30<
> [plustek] sane_get_devices (0xbfbfe6d8, 0)
> device `plustek:/dev/uscanner0' is a Canon
N1240U/LiDE30 USB flatbed
> scanner
> [plustek] sane_exit
> [plustek] Shutdown called (dev->fd=-1,
/dev/uscanner0)
> [plustek] Waiting for scanner-ready...
>
> Thanks,
> Xihong
>
>
>
>
> On Fri, 10 Nov 2006, Gerhard Jaeger wrote:
>
> > On Thursday 09 November 2006 19:47, Xihong Yin
wrote:
> > > Hi,
> > >
> > > sane-find-scanner can find the scanner on
/dev/uscanner0, but don't know
> > > the manufactor and the model. output of
sane-find-scanner is
> > >
> > > ----------------
> > > found USB scanner (UNKNOWN vendor and
product) at device /dev/uscanner0
> > > ---------------
> > >
> > > output of "scanimage -L" is
> > > ----------------------------
> > > No scanners were identified. If you were
expecting something different,
> > > check that the scanner is plugged in, turned
on and detected by the
> > > sane-find-scanner tool (if appropriate).
Please read the documentation
> > > which came with this software (README, FAQ,
manpages).
> > > --------------------------
> > >
> > > I tried to configure the backend
'plustek.conf' to provide vender ID and
> > > product ID. But scanimage is still not
working. "scanimage -L" just hangs
> > > there and no output.
> > >
> > > After setting the DEBUG environmental
variable, the 'scanimage -L' outputs
> > > a message of 'waiting for scanner-ready' and
stucks there.
> > >
> > Hi,
> >
> > I suspect a problem in the underlying
USB-subsystem.
> > Could you please post the output of
> > SANE_DEBUG_PLUSTEK=19
> >
> > - Gerhard
> >
> >
> > --
> > sane-devel mailing list: sane-devellists.alioth.debian.org
> > http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
> > Unsubscribe: Send mail with subject
"unsubscribe your_password"
> > to sane-devel-requestlists.alioth.debian.org
> >
>
>
--
:wq
.--------------------------------------------------------.
, , , _ | GS(IT)/MU d- a- C++ UB/L++(++++)>$
P--- E--- PS+++(+) |
/|/| /| /_| | PE(--)>+ Y+(++) t++ 5++ X++ R*(+) b+>++
e++
h*> r++ |
/ | |/-|/__/
`--------------------------------------------------------'
--
sane-devel mailing list: sane-devellists.alioth.debian.org
http://lists.alioth.debian.org/mailman/listinfo/sane-d
evel
Unsubscribe: Send mail with subject "unsubscribe
your_password"
to sane-devel-requestlists.alioth.debian.org
|
|
[1-4]
|
|