par. ata not seen if sata is present

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

First let me note several facts then ask the question:

~    * The PATA drives in question used to work under
8-current AMD64 
(last time I tried it was about 3 months ago) if the SATA
drive was 
connected (see dmesg output below for details) on the same
mother board 
[only hardware difference is I added a pci-e video card
replacing the 
pci one I had]

~    * The BIOS doesn't see them (thus FreeBSD doesn't see
them [I 
already am aware of this])

~    * Vista *DOES* see them

~    * I tried every jumper and cable combo (even a low
grade IDE cable 
and a UDMA133 cable)

~    * The BIOS only has two settings relating to IDE
(besides for drive 
autodetect) bus master and if the ata chip should support
IDE or not (I 
tried both and the only effect was if it was not set to
support IDE no 
drives what so ever are seen).

Diag output from FreeBSD:

atacontrol list:

ATA channel 2:
~    Master:      no device present
~    Slave:       no device present
ATA channel 3:
~    Master:      no device present
~    Slave:       no device present
ATA channel 4:
~    Master:  ad8 <ST3500630AS/3.AAE> Serial ATA II
~    Slave:       no device present
ATA channel 5:
~    Master:      no device present
~    Slave:       no device present
ATA channel 6:
~    Master:      no device present
~    Slave:       no device present
ATA channel 7:
~    Master:      no device present

Note: shouldn't ata4 be ata2 or something close since the
phsyical cable 
is plugged into SATA1 (there is no SATA0) on the mother
board

dmesg|grep ata:

atapci0: <Marvell ATA controller> port 
0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd4
00-0xd40f 
mem 0xfeaffc00-0xfeafffff irq 16 at device 0.0 on pci3
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
atapci1: <Intel ICH9 SATA300 controller> port 
0xb000-0xb007,0xac00-0xac03,0xa880-0xa887,0xa800-0xa803,0xa4
80-0xa48f,0xa400-0xa40f 
irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
atapci2: <Intel ICH9 SATA300 controller> port 
0xa000-0xa007,0x9c00-0x9c03,0x9880-0x9887,0x9800-0x9803,0x94
80-0x948f,0x9400-0x940f 
irq 19 at device 31.5 on pci0
atapci2: [ITHREAD]
ata6: <ATA channel 0> on atapci2
ata6: [ITHREAD]
ata7: <ATA channel 1> on atapci2
ata7: [ITHREAD]
ad8: 476940MB <Seagate ST3500630AS 3.AAE> at
ata4-master SATA300



-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.9 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iEYEARECAAYFAkg6TLwACgkQk8GFzCrQm4CgMQCgrOS0k/l4Qb9O/LHxIUhi
fKOl
8bAAoLW2CRg/p9LLdiV90prXmi3yBwVl
=74AZ
-----END PGP SIGNATURE-----

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

Aryeh M. Friedman wrote:
> atapci0: <Marvell ATA controller> port 
>
0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd4
00-0xd40f 
> mem 0xfeaffc00-0xfeafffff irq 16 at device 0.0 on pci3

I think it's Marvell 88SE61xx controller. It isn't
supported.
Can you show `pciconf -l` output?

-- 
WBR, Andrey V. Elsukov
_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Andrey V. Elsukov wrote:
| Aryeh M. Friedman wrote:
|> atapci0: <Marvell ATA controller> port 
0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd4
00-0xd40f 
mem 0xfeaffc00-0xfeafffff irq 16 at device 0.0 on pci3
|
| I think it's Marvell 88SE61xx controller. It isn't
supported.
| Can you show `pciconf -l` output?
|
hostb0pci0:0:0:0:    class=0x060000 card=0x73601462
chip=0x29c08086 
rev=0x02 hdr=0x00
pcib1pci0:0:1:0:    class=0x060400 card=0x00008086
chip=0x29c18086 
rev=0x02 hdr=0x01
uhci0pci0:0:26:0:    class=0x0c0300 card=0x73601462
chip=0x29378086 
rev=0x02 hdr=0x00
uhci1pci0:0:26:1:    class=0x0c0300 card=0x73601462
chip=0x29388086 
rev=0x02 hdr=0x00
ehci0pci0:0:26:7:    class=0x0c0320 card=0x73601462
chip=0x293c8086 
rev=0x02 hdr=0x00
pcm0pci0:0:27:0:    class=0x040300 card=0x73601462
chip=0x293e8086 
rev=0x02 hdr=0x00
pcib2pci0:0:28:0:    class=0x060400 card=0x73601462
chip=0x29408086 
rev=0x02 hdr=0x01
pcib3pci0:0:28:4:    class=0x060400 card=0x73601462
chip=0x29488086 
rev=0x02 hdr=0x01
pcib4pci0:0:28:5:    class=0x060400 card=0x73601462
chip=0x294a8086 
rev=0x02 hdr=0x01
uhci2pci0:0:29:0:    class=0x0c0300 card=0x73601462
chip=0x29348086 
rev=0x02 hdr=0x00
uhci3pci0:0:29:1:    class=0x0c0300 card=0x73601462
chip=0x29358086 
rev=0x02 hdr=0x00
uhci4pci0:0:29:2:    class=0x0c0300 card=0x73601462
chip=0x29368086 
rev=0x02 hdr=0x00
uhci5pci0:0:29:3:    class=0x0c0300 card=0x73601462
chip=0x29398086 
rev=0x02 hdr=0x00
ehci1pci0:0:29:7:    class=0x0c0320 card=0x73601462
chip=0x293a8086 
rev=0x02 hdr=0x00
pcib5pci0:0:30:0:    class=0x060401 card=0x73601462
chip=0x244e8086 
rev=0x92 hdr=0x01
isab0pci0:0:31:0:    class=0x060100 card=0x73601462
chip=0x29188086 
rev=0x02 hdr=0x00
atapci1pci0:0:31:2:    class=0x01018f card=0x73601462
chip=0x29218086 
rev=0x02 hdr=0x00
none0pci0:0:31:3:    class=0x0c0500 card=0x73601462
chip=0x29308086 
rev=0x02 hdr=0x00
atapci2pci0:0:31:5:    class=0x010185 card=0x73601462
chip=0x29268086 
rev=0x02 hdr=0x00
vgapci0pci0:1:0:0:    class=0x030000 card=0xc7333842
chip=0x040410de 
rev=0xa1 hdr=0x00
atapci0pci0:3:0:0:    class=0x01018f card=0x612111ab
chip=0x612111ab 
rev=0xb1 hdr=0x00
re0pci0:4:0:0:    class=0x020000 card=0x360c1462
chip=0x816810ec 
rev=0x01 hdr=0x00

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.9 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iEYEARECAAYFAkg6ZTwACgkQk8GFzCrQm4DqagCfdxF8BO8yDqnbCPEI2lNp
W6JI
2LsAn25+SWce38ZnjN+zdfBIVQWkbqgJ
=4fc+
-----END PGP SIGNATURE-----

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Andrey Chernov wrote:
| On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M.
Friedman wrote:
|> atapci0pci0:3:0:0:    class=0x01018f
card=0x612111ab chip=0x612111ab
|> rev=0xb1 hdr=0x00
|
| See also "atadev->param.model problem or bug with
Marvell 88SE6811 chip"
| thread in current
|
I tried the patch in that thread:

-
------------------------------------------------------------
--
|>> stage 3.2: building everything
-
------------------------------------------------------------
--
cd /usr/obj/usr/src/sys/MONSTER; MAKEOBJDIRPREFIX=/usr/obj 

MACHINE_ARCH=amd64  MACHINE=amd64  CPUTYPE=nocona  
GROFF_BIN_PATH=/usr/obj/usr/src/tmp/legacy/usr/bin  
GROFF_FONT_PATH=/usr/obj/usr/src/tmp/legacy/usr/share/groff_
font  
GROFF_TMAC_PATH=/usr/obj/usr/src/tmp/legacy/usr/share/tmac 

_SHLIBDIRPREFIX=/usr/obj/usr/src/tmp  VERSION="FreeBSD
8.0-CURRENT amd64 
800037"  INSTALL="sh
/usr/src/tools/install.sh"  
PATH=/usr/obj/usr/src/tmp/legacy/usr/sbin:/usr/obj/usr/src/t
mp/legacy/usr/bin:/usr/obj/usr/src/tmp/legacy/usr/games:/usr
/obj/usr/src/tmp/usr/sbin:/usr/obj/usr/src/tmp/usr/bin:/usr/
obj/usr/src/tmp/usr/games:/sbin:/bin:/usr/sbin:/usr/bin 
NO_CTF=1 make KERNEL=kernel all -DNO_MODULES_OBJ
cc -c -O2 -frename-registers -pipe -fno-strict-aliasing
-march=nocona 
-std=c99  -Wall -Wredundant-decls -Wnested-externs
-Wstrict-prototypes  
-Wmissing-prototypes -Wpointer-arith -Winline -Wcast-qual 
-Wundef 
-Wno-pointer-sign -fformat-extensions -nostdinc  -I.
-I/usr/src/sys 
-I/usr/src/sys/contrib/altq -D_KERNEL
-DHAVE_KERNEL_OPTION_HEADERS 
-include opt_global.h -fno-common -finline-limit=8000
--param 
inline-unit-growth=100 --param large-function-growth=1000  
-mcmodel=kernel -mno-red-zone  -mfpmath=387 -mno-sse
-mno-sse2 -mno-sse3 
-mno-mmx -mno-3dnow  -msoft-float
-fno-asynchronous-unwind-tables 
-ffreestanding -Werror  /usr/src/sys/dev/ata/ata-all.c;
/usr/src/sys/dev/ata/ata-all.c: In function 'ata_getparam':
/usr/src/sys/dev/ata/ata-all.c:610: error: 'struct
ata_device' has no 
member named 'config'
/usr/src/sys/dev/ata/ata-all.c:611: error: 'struct
ata_device' has no 
member named 'reserved2'

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.9 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iEYEARECAAYFAkg6Z30ACgkQk8GFzCrQm4AuOwCgysw4y6/gQh3cIEYr53Vc
YqlZ
CAcAoI2NO5kpZn9PMIwUTeI+oClZZ3H1
=r1BV
-----END PGP SIGNATURE-----

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

Aryeh M. Friedman wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
> 
> Andrey Chernov wrote:
> | On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M.
Friedman wrote:
> |> atapci0pci0:3:0:0:    class=0x01018f
card=0x612111ab chip=0x612111ab
> |> rev=0xb1 hdr=0x00
> |
> | See also "atadev->param.model problem or bug
with Marvell 88SE6811 chip"
> | thread in current
> |
> I tried the patch in that thread:

It has mistake.. :-
And it doesn't resolve the problem.

-- 
WBR, Andrey V. Elsukov
_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

Hi

Hi!

The param->model problem is a side effect of ATA not
supporting this  
chip.

The marvell chips apparently need special support to work
properly, so  
I need to have the HW here for "hands on"
development (marvell doesn't  
hand out docs).

Same routine as for the last decade, get me the HW and I'll
work out  
how to support it if at all possible.

-Søren




On 26May, 2008, at 9:32 , Aryeh M. Friedman wrote:

> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Andrey Chernov wrote:
> | On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M.
Friedman wrote:
> |> atapci0pci0:3:0:0:    class=0x01018f
card=0x612111ab  
> chip=0x612111ab
> |> rev=0xb1 hdr=0x00
> |
> | See also "atadev->param.model problem or bug
with Marvell 88SE6811  
> chip"
> | thread in current
> |
> I tried the patch in that thread:
>
> -
------------------------------------------------------------
--
> |>> stage 3.2: building everything
> -
------------------------------------------------------------
--
> cd /usr/obj/usr/src/sys/MONSTER;
MAKEOBJDIRPREFIX=/usr/obj   
> MACHINE_ARCH=amd64  MACHINE=amd64  CPUTYPE=nocona 
GROFF_BIN_PATH=/ 
> usr/obj/usr/src/tmp/legacy/usr/bin 
GROFF_FONT_PATH=/usr/obj/usr/src/ 
> tmp/legacy/usr/share/groff_font 
GROFF_TMAC_PATH=/usr/obj/usr/src/ 
> tmp/legacy/usr/share/tmac 
_SHLIBDIRPREFIX=/usr/obj/usr/src/tmp   
> VERSION="FreeBSD 8.0-CURRENT amd64 800037" 
INSTALL="sh /usr/src/ 
> tools/install.sh" 
PATH=/usr/obj/usr/src/tmp/legacy/usr/sbin:/usr/ 
>
obj/usr/src/tmp/legacy/usr/bin:/usr/obj/usr/src/tmp/legacy/u
sr/ 
>
games:/usr/obj/usr/src/tmp/usr/sbin:/usr/obj/usr/src/tmp/usr
/bin:/ 
>
usr/obj/usr/src/tmp/usr/games:/sbin:/bin:/usr/sbin:/usr/bin
NO_CTF=1  
> make KERNEL=kernel all -DNO_MODULES_OBJ
> cc -c -O2 -frename-registers -pipe -fno-strict-aliasing
- 
> march=nocona -std=c99  -Wall -Wredundant-decls
-Wnested-externs - 
> Wstrict-prototypes  -Wmissing-prototypes
-Wpointer-arith -Winline - 
> Wcast-qual  -Wundef -Wno-pointer-sign
-fformat-extensions -nostdinc   
> -I. -I/usr/src/sys -I/usr/src/sys/contrib/altq
-D_KERNEL - 
> DHAVE_KERNEL_OPTION_HEADERS -include opt_global.h
-fno-common - 
> finline-limit=8000 --param inline-unit-growth=100
--param large- 
> function-growth=1000  -mcmodel=kernel -mno-red-zone 
-mfpmath=387 - 
> mno-sse -mno-sse2 -mno-sse3 -mno-mmx -mno-3dnow 
-msoft-float -fno- 
> asynchronous-unwind-tables -ffreestanding -Werror 
/usr/src/sys/dev/ 
> ata/ata-all.c;
> /usr/src/sys/dev/ata/ata-all.c: In function
'ata_getparam':
> /usr/src/sys/dev/ata/ata-all.c:610: error: 'struct
ata_device' has  
> no member named 'config'
> /usr/src/sys/dev/ata/ata-all.c:611: error: 'struct
ata_device' has  
> no member named 'reserved2'
>
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v2.0.9 (FreeBSD)
> Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

>
>
iEYEARECAAYFAkg6Z30ACgkQk8GFzCrQm4AuOwCgysw4y6/gQh3cIEYr53Vc
YqlZ
> CAcAoI2NO5kpZn9PMIwUTeI+oClZZ3H1
> =r1BV
> -----END PGP SIGNATURE-----
>
> _______________________________________________
> freebsd-currentfreebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
> To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org 
> "
>

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Andrey V. Elsukov wrote:
| Aryeh M. Friedman wrote:
|> -----BEGIN PGP SIGNED MESSAGE-----
|> Hash: SHA1
|>
|> Andrey Chernov wrote:
|> | On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M.
Friedman wrote:
|> |> atapci0pci0:3:0:0:    class=0x01018f
card=0x612111ab chip=0x612111ab
|> |> rev=0xb1 hdr=0x00
|> |
|> | See also "atadev->param.model problem or bug
with Marvell 88SE6811 
chip"
|> | thread in current
|> |
|> I tried the patch in that thread:
|
| It has mistake.. :-
| And it doesn't resolve the problem.
|
So do Chernov's advice or not?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.9 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iEYEARECAAYFAkg6aSgACgkQk8GFzCrQm4Ah1gCdHz/3JeAUhEHxgcvyYI6M
Nbzq
9acAoOXiwEaqfHkrFkHsZmcUkCyJiCW9
=btgw
-----END PGP SIGNATURE-----

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

On Mon, May 26, 2008 at 03:32:14AM -0400, Aryeh M. Friedman
wrote:
> I tried the patch in that thread:

You need to change struct members to atadev->param.config
and 
atadev->param.reserved2  (i.e. insert "param.")
since there is no such 
members in atadev directly.

-- 
http://ache.pp.ru/
_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M. Friedman
wrote:
> atapci0pci0:3:0:0:    class=0x01018f card=0x612111ab
chip=0x612111ab 
> rev=0xb1 hdr=0x00

See also "atadev->param.model problem or bug with
Marvell 88SE6811 chip" 
thread in current

-- 
http://ache.pp.ru/
_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I can't send you the machine but can you do it remotely?


Søren Schmidt wrote:
| Hi
|
| Hi!
|
| The param->model problem is a side effect of ATA not
supporting this chip.
|
| The marvell chips apparently need special support to work
properly, so 
I need to have the HW here for "hands on"
development (marvell doesn't 
hand out docs).
|
| Same routine as for the last decade, get me the HW and
I'll work out 
how to support it if at all possible.
|
| -Søren
|
|
|
|
| On 26May, 2008, at 9:32 , Aryeh M. Friedman wrote:
|
| Andrey Chernov wrote:
| | On Mon, May 26, 2008 at 03:22:37AM -0400, Aryeh M.
Friedman wrote:
| |> atapci0pci0:3:0:0:    class=0x01018f
card=0x612111ab chip=0x612111ab
| |> rev=0xb1 hdr=0x00
| |
| | See also "atadev->param.model problem or bug
with Marvell 88SE6811 chip"
| | thread in current
| |
| I tried the patch in that thread:
|
|
------------------------------------------------------------
--
| |>> stage 3.2: building everything
|
------------------------------------------------------------
--
| cd /usr/obj/usr/src/sys/MONSTER; MAKEOBJDIRPREFIX=/usr/obj
 
MACHINE_ARCH=amd64  MACHINE=amd64  CPUTYPE=nocona  
GROFF_BIN_PATH=/usr/obj/usr/src/tmp/legacy/usr/bin  
GROFF_FONT_PATH=/usr/obj/usr/src/tmp/legacy/usr/share/groff_
font  
GROFF_TMAC_PATH=/usr/obj/usr/src/tmp/legacy/usr/share/tmac 

_SHLIBDIRPREFIX=/usr/obj/usr/src/tmp  VERSION="FreeBSD
8.0-CURRENT amd64 
800037"  INSTALL="sh
/usr/src/tools/install.sh"  
PATH=/usr/obj/usr/src/tmp/legacy/usr/sbin:/usr/obj/usr/src/t
mp/legacy/usr/bin:/usr/obj/usr/src/tmp/legacy/usr/games:/usr
/obj/usr/src/tmp/usr/sbin:/usr/obj/usr/src/tmp/usr/bin:/usr/
obj/usr/src/tmp/usr/games:/sbin:/bin:/usr/sbin:/usr/bin 
NO_CTF=1 make KERNEL=kernel all -DNO_MODULES_OBJ
| cc -c -O2 -frename-registers -pipe -fno-strict-aliasing
-march=nocona 
-std=c99  -Wall -Wredundant-decls -Wnested-externs
-Wstrict-prototypes  
-Wmissing-prototypes -Wpointer-arith -Winline -Wcast-qual 
-Wundef 
-Wno-pointer-sign -fformat-extensions -nostdinc  -I.
-I/usr/src/sys 
-I/usr/src/sys/contrib/altq -D_KERNEL
-DHAVE_KERNEL_OPTION_HEADERS 
-include opt_global.h -fno-common -finline-limit=8000
--param 
inline-unit-growth=100 --param large-function-growth=1000  
-mcmodel=kernel -mno-red-zone  -mfpmath=387 -mno-sse
-mno-sse2 -mno-sse3 
-mno-mmx -mno-3dnow  -msoft-float
-fno-asynchronous-unwind-tables 
-ffreestanding -Werror  /usr/src/sys/dev/ata/ata-all.c;
| /usr/src/sys/dev/ata/ata-all.c: In function
'ata_getparam':
| /usr/src/sys/dev/ata/ata-all.c:610: error: 'struct
ata_device' has no 
member named 'config'
| /usr/src/sys/dev/ata/ata-all.c:611: error: 'struct
ata_device' has no 
member named 'reserved2'
|
|>
_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"
|>

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.9 (FreeBSD)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iEYEARECAAYFAkg6aXsACgkQk8GFzCrQm4DVFgCfS+JUAEJoDn8McxrILqAT
+fYI
faYAnji0tYuA0se6HwCeTx1JBVRIjpn7
=og2b
-----END PGP SIGNATURE-----

_______________________________________________
freebsd-currentfreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-curre
nt
To unsubscribe, send any mail to
"freebsd-current-unsubscribefreebsd.org"