support for Proxim Silver wifi card

Hi all,

does anybody have a clue why Athreos-based Proxim Orinoco
11a/b/g
cards are not supported in 7.0?

pciconf -lv:

ath0pci0:22:0:0:       class=0x020000 card=0xaa1014b7
chip=0x0013168c
rev=0x01
hdr=0x00
    vendor     = 'Atheros Communications Inc.'
    device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
    class      = network
    subclass   = ethernet

dmesg:

cardbus0: Expecting link target, got 0x0
ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff irq 16
at device 0.0 on
cardbus0
ath0: [ITHREAD]
ath0: unable to attach hardware; HAL status 13
device_attach: ath0 attach returned 6

HAL status 13 says unsupported HW. Has anybody worked on
this?
Is it matter of just some missing ID or is there a more
fundamental
problem?

Thanks,
Petr

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Your revision of the card is not supported. Bad luck, switch
to Linux.

On Fri, Feb 29, 2008 at 9:01 PM, Petr Holub <hopetics.muni.cz> wrote:
> Hi all,
>
>  does anybody have a clue why Athreos-based Proxim
Orinoco 11a/b/g
>  cards are not supported in 7.0?
>
>  pciconf -lv:
>
>  ath0pci0:22:0:0:       class=0x020000 card=0xaa1014b7
chip=0x0013168c
>  rev=0x01
>  hdr=0x00
>     vendor     = 'Atheros Communications Inc.'
>     device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
>     class      = network
>     subclass   = ethernet
>
>  dmesg:
>
>  cardbus0: Expecting link target, got 0x0
>  ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff
irq 16 at device 0.0 on
>  cardbus0
>  ath0: [ITHREAD]
>  ath0: unable to attach hardware; HAL status 13
>  device_attach: ath0 attach returned 6
>
>  HAL status 13 says unsupported HW. Has anybody worked
on this?
>  Is it matter of just some missing ID or is there a
more fundamental
>  problem?
>
>  Thanks,
>  Petr
>
>  _______________________________________________
>  freebsd-hardwarefreebsd.org mailing list
>  http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
>  To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"
>
_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Petr Holub wrote:
> Hi all,
>
> does anybody have a clue why Athreos-based Proxim
Orinoco 11a/b/g
> cards are not supported in 7.0?
>
> pciconf -lv:
>
> ath0pci0:22:0:0:       class=0x020000 card=0xaa1014b7
chip=0x0013168c
> rev=0x01
> hdr=0x00
>     vendor     = 'Atheros Communications Inc.'
>     device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
>     class      = network
>     subclass   = ethernet
>
> dmesg:
>
> cardbus0: Expecting link target, got 0x0
> ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff
irq 16 at device 0.0 on
> cardbus0
> ath0: [ITHREAD]
> ath0: unable to attach hardware; HAL status 13
> device_attach: ath0 attach returned 6
>
> HAL status 13 says unsupported HW. Has anybody worked
on this?
> Is it matter of just some missing ID or is there a more
fundamental
> problem?
>   

It should work (devid 0x13 is supported by the hal in cvs). 
You can try 
the test hal at http://www.freebsd.org/~
sam.  If that works please let 
me know what it identifies the mac+phy as.

    Sam

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

> It should work (devid 0x13 is supported by the hal in
cvs).  You can try
> the test hal at http://www.freebsd.org/~
sam.  If that works please let
> me know what it identifies the mac+phy as.

It took as long as till today for me to get my hands back on
that
HW. What I did I took HAL from your website, replaced
/usr/src/sys/contrib/dev/ath
directory and did
make buildkernel && make install kernel
(the machine is normal 7.0-RELEASE so I've build standard
GENERIC
kernel with only HAL changed)

The cards (this time I did the test with both SILVER and
GOLD
version of that Proxim card) obviously don't work even with
this HAL.
I've tried to gather as much information as possible - see
below.
Let me know if you need something more.

Thanks a lot,
Petr

============================================================

PROXIM Gold:
============================================================


info:

Proxim GOLD 802.11a/b/g ComboCard
Model: 8480-WD
MAC-Address: 0020A64C5F02
SN: 03MT20004729
P/N: 64730/A

dmesg (verbose):

pcib7: requested memory range 0x88000000-0xffffffff: good
cbb0: Opening memory:
cbb0: Normal: 0xbfeb0000-0xbfebffff
unknown: Lazy allocation of 0x10000 bytes rid 0x10 type 3 at
0xbfeb0000
cardbus0: Expecting link target, got 0x0
cbb0: Opening memory:
        map[10]: type Memory, range 32, base 0, size 16,
enabled
pcib7: requested memory range 0x88000000-0xffffffff: good
found-> vendor=0x168c, dev=0x0013, revid=0x01
        domain=0, bus=22, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0002, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns),
maxlat=0x1c (7000 ns)
        intpin=a, irq=16
        powerspec 2  supports D0 D3  current D0
ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff irq 16
at device 0.0 on
cardbus0
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
cbb0: Opening memory:
cbb0: Normal: 0xbfeb0000-0xbfebffff
ath0: [MPSAFE]
ath0: [ITHREAD]
ath0: unable to attach hardware; HAL status 13
cbb0: Opening memory:
device_attach: ath0 attach returned 6


pciconf -lvc:

ath0pci0:22:0:0:       class=0x020000 card=0x0a1014b7
chip=0x0013168c
rev=0x01 hdr=0x00
    vendor     = 'Atheros Communications Inc.'
    device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
    class      = network
    subclass   = ethernet

============================================================

PROXIM Silver:
============================================================


info:

Proxim SILVER 802.11a/b/g ComboCard
Model: 8481-WD
MAC-Address: 0020A64C713A
SN: 03MT21000304
P/N: 64738/A

dmesg (verbose):

pcib7: requested memory range 0x88000000-0xffffffff: good
cbb0: Opening memory:
cbb0: Normal: 0xbfeb0000-0xbfebffff
unknown: Lazy allocation of 0x10000 bytes rid 0x10 type 3 at
0xbfeb0000
cardbus0: Expecting link target, got 0x0
cbb0: Opening memory:
        map[10]: type Memory, range 32, base 0, size 16,
enabled
pcib7: requested memory range 0x88000000-0xffffffff: good
found-> vendor=0x168c, dev=0x0013, revid=0x01
        domain=0, bus=22, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0002, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns),
maxlat=0x1c (7000 ns)
        intpin=a, irq=16
        powerspec 2  supports D0 D3  current D0
ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff irq 16
at device 0.0 on
cardbus0
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
cbb0: Opening memory:
cbb0: Normal: 0xbfeb0000-0xbfebffff
ath0: [MPSAFE]
ath0: [ITHREAD]
ath0: unable to attach hardware; HAL status 13
cbb0: Opening memory:
device_attach: ath0 attach returned 6

pciconf -lvc:

ath0pci0:22:0:0:       class=0x020000 card=0xaa1014b7
chip=0x0013168c
rev=0x01 hdr=0x00
    vendor     = 'Atheros Communications Inc.'
    device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
    class      = network
    subclass   = ethernet

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Sam,

any clues about the problem below? I'm starting to suspect
the
problem might actually be something around CardBus, as
others
have reported similar problems:
http://www
.mail-archive.com/freebsd-stablefreebsd.org/msg91307.html
I'm also using T61p laptop. Maybe something that prevents
the cards
from being init'd properly?

Petr

============================================================
====
                            Petr Holub
CESNET z.s.p.o.                       Supercomputing Center
Brno
Zikova 4                             Institute of Compt.
Science
162 00 Praha 6, CZ                            Masaryk
University
Czech Republic                     Botanicka 68a, 60200
Brno, CZ 
e-mail: Petr.Holubcesnet.cz               phone:
+420-549493944
                                             fax:
+420-541212747
                                       e-mail: hopetics.muni.cz


> -----Original Message-----
> From: Petr Holub [mailto:hopetics.muni.cz]
> Sent: Thursday, March 06, 2008 1:52 PM
> To: 'Sam Leffler'
> Cc: 'freebsd-hardwarefreebsd.org'
> Subject: RE: support for Proxim Silver wifi card
> 
> > It should work (devid 0x13 is supported by the hal
in cvs).  You can try
> > the test hal at http://www.freebsd.org/~
sam.  If that works please let
> > me know what it identifies the mac+phy as.
> 
> It took as long as till today for me to get my hands
back on that
> HW. What I did I took HAL from your website, replaced
> /usr/src/sys/contrib/dev/ath
> directory and did
> make buildkernel && make install kernel
> (the machine is normal 7.0-RELEASE so I've build
standard GENERIC
> kernel with only HAL changed)
> 
> The cards (this time I did the test with both SILVER
and GOLD
> version of that Proxim card) obviously don't work even
with this HAL.
> I've tried to gather as much information as possible -
see below.
> Let me know if you need something more.
> 
> Thanks a lot,
> Petr
> 
>
============================================================

> PROXIM Gold:
>
============================================================

> 
> info:
> 
> Proxim GOLD 802.11a/b/g ComboCard
> Model: 8480-WD
> MAC-Address: 0020A64C5F02
> SN: 03MT20004729
> P/N: 64730/A
> 
> dmesg (verbose):
> 
> pcib7: requested memory range 0x88000000-0xffffffff:
good
> cbb0: Opening memory:
> cbb0: Normal: 0xbfeb0000-0xbfebffff
> unknown: Lazy allocation of 0x10000 bytes rid 0x10 type
3 at 0xbfeb0000
> cardbus0: Expecting link target, got 0x0
> cbb0: Opening memory:
>         map[10]: type Memory, range 32, base 0, size
16, enabled
> pcib7: requested memory range 0x88000000-0xffffffff:
good
> found-> vendor=0x168c, dev=0x0013, revid=0x01
>         domain=0, bus=22, slot=0, func=0
>         class=02-00-00, hdrtype=0x00, mfdev=0
>         cmdreg=0x0002, statreg=0x0290, cachelnsz=0
(dwords)
>         lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns),
maxlat=0x1c (7000 ns)
>         intpin=a, irq=16
>         powerspec 2  supports D0 D3  current D0
> ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff
irq 16 at device 0.0 on
> cardbus0
> ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
> cbb0: Opening memory:
> cbb0: Normal: 0xbfeb0000-0xbfebffff
> ath0: [MPSAFE]
> ath0: [ITHREAD]
> ath0: unable to attach hardware; HAL status 13
> cbb0: Opening memory:
> device_attach: ath0 attach returned 6
> 
> 
> pciconf -lvc:
> 
> ath0pci0:22:0:0:       class=0x020000 card=0x0a1014b7
chip=0x0013168c
> rev=0x01 hdr=0x00
>     vendor     = 'Atheros Communications Inc.'
>     device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
>     class      = network
>     subclass   = ethernet
> 
>
============================================================

> PROXIM Silver:
>
============================================================

> 
> info:
> 
> Proxim SILVER 802.11a/b/g ComboCard
> Model: 8481-WD
> MAC-Address: 0020A64C713A
> SN: 03MT21000304
> P/N: 64738/A
> 
> dmesg (verbose):
> 
> pcib7: requested memory range 0x88000000-0xffffffff:
good
> cbb0: Opening memory:
> cbb0: Normal: 0xbfeb0000-0xbfebffff
> unknown: Lazy allocation of 0x10000 bytes rid 0x10 type
3 at 0xbfeb0000
> cardbus0: Expecting link target, got 0x0
> cbb0: Opening memory:
>         map[10]: type Memory, range 32, base 0, size
16, enabled
> pcib7: requested memory range 0x88000000-0xffffffff:
good
> found-> vendor=0x168c, dev=0x0013, revid=0x01
>         domain=0, bus=22, slot=0, func=0
>         class=02-00-00, hdrtype=0x00, mfdev=0
>         cmdreg=0x0002, statreg=0x0290, cachelnsz=0
(dwords)
>         lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns),
maxlat=0x1c (7000 ns)
>         intpin=a, irq=16
>         powerspec 2  supports D0 D3  current D0
> ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff
irq 16 at device 0.0 on
> cardbus0
> ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
> cbb0: Opening memory:
> cbb0: Normal: 0xbfeb0000-0xbfebffff
> ath0: [MPSAFE]
> ath0: [ITHREAD]
> ath0: unable to attach hardware; HAL status 13
> cbb0: Opening memory:
> device_attach: ath0 attach returned 6
> 
> pciconf -lvc:
> 
> ath0pci0:22:0:0:       class=0x020000 card=0xaa1014b7
chip=0x0013168c
> rev=0x01 hdr=0x00
>     vendor     = 'Atheros Communications Inc.'
>     device     = 'AR5212, AR5213 802.11a/b/g Wireless
Adapter'
>     class      = network
>     subclass   = ethernet

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Hal status 13 (HAL_ENOTSUPP from ah.h) means the info read
from the card 
at attach indicated a device that's not supported.  Given
the pci device 
id I am guessing the card really is supported though vendors
sometimes 
re-use old pci device id's with newer parts (0x13 is a
generate 5212 
identified).  If the hal simply couldn't read the necessary
registers 
you could also get this error.  If you can plug this card
into another 
system and it works then you know it's an issue w/ support
on your 
laptop.  I happen to have a t61p and just tried a bunch of
different 
cards (including one w/ this device id) and all the cards I
expected to 
work so the best I can suggest is you try the card in
another laptop.

I don't have one of these cards to test but I do have cards
w/ just 
about every Atheros part (except for the newest 11n parts).

     Sam

Petr Holub wrote:
> Sam,
>
> any clues about the problem below? I'm starting to
suspect the
> problem might actually be something around CardBus, as
others
> have reported similar problems:
> http://www
.mail-archive.com/freebsd-stablefreebsd.org/msg91307.html
> I'm also using T61p laptop. Maybe something that
prevents the cards
> from being init'd properly?
>
> Petr
>
>
============================================================
====
>                             Petr Holub
> CESNET z.s.p.o.                       Supercomputing
Center Brno
> Zikova 4                             Institute of
Compt. Science
> 162 00 Praha 6, CZ                            Masaryk
University
> Czech Republic                     Botanicka 68a, 60200
Brno, CZ 
> e-mail: Petr.Holubcesnet.cz               phone:
+420-549493944
>                                              fax:
+420-541212747
>                                        e-mail:
hopetics.muni.cz
>
>
>   
>> -----Original Message-----
>> From: Petr Holub [mailto:hopetics.muni.cz]
>> Sent: Thursday, March 06, 2008 1:52 PM
>> To: 'Sam Leffler'
>> Cc: 'freebsd-hardwarefreebsd.org'
>> Subject: RE: support for Proxim Silver wifi card
>>
>>     
>>> It should work (devid 0x13 is supported by the
hal in cvs).  You can try
>>> the test hal at http://www.freebsd.org/~
sam.  If that works please let
>>> me know what it identifies the mac+phy as.
>>>       
>> It took as long as till today for me to get my
hands back on that
>> HW. What I did I took HAL from your website,
replaced
>> /usr/src/sys/contrib/dev/ath
>> directory and did
>> make buildkernel && make install kernel
>> (the machine is normal 7.0-RELEASE so I've build
standard GENERIC
>> kernel with only HAL changed)
>>
>> The cards (this time I did the test with both
SILVER and GOLD
>> version of that Proxim card) obviously don't work
even with this HAL.
>> I've tried to gather as much information as
possible - see below.
>> Let me know if you need something more.
>>
>> Thanks a lot,
>> Petr
>>
>>
============================================================

>> PROXIM Gold:
>>
============================================================

>>
>> info:
>>
>> Proxim GOLD 802.11a/b/g ComboCard
>> Model: 8480-WD
>> MAC-Address: 0020A64C5F02
>> SN: 03MT20004729
>> P/N: 64730/A
>>
>> dmesg (verbose):
>>
>> pcib7: requested memory range
0x88000000-0xffffffff: good
>> cbb0: Opening memory:
>> cbb0: Normal: 0xbfeb0000-0xbfebffff
>> unknown: Lazy allocation of 0x10000 bytes rid 0x10
type 3 at 0xbfeb0000
>> cardbus0: Expecting link target, got 0x0
>> cbb0: Opening memory:
>>         map[10]: type Memory, range 32, base 0,
size 16, enabled
>> pcib7: requested memory range
0x88000000-0xffffffff: good
>> found-> vendor=0x168c, dev=0x0013, revid=0x01
>>         domain=0, bus=22, slot=0, func=0
>>         class=02-00-00, hdrtype=0x00, mfdev=0
>>         cmdreg=0x0002, statreg=0x0290, cachelnsz=0
(dwords)
>>         lattimer=0x00 (0 ns), mingnt=0x0a (2500
ns), maxlat=0x1c (7000 ns)
>>         intpin=a, irq=16
>>         powerspec 2  supports D0 D3  current D0
>> ath0: <Atheros 5212> mem
0xbfeb0000-0xbfebffff irq 16 at device 0.0 on
>> cardbus0
>> ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
>> cbb0: Opening memory:
>> cbb0: Normal: 0xbfeb0000-0xbfebffff
>> ath0: [MPSAFE]
>> ath0: [ITHREAD]
>> ath0: unable to attach hardware; HAL status 13
>> cbb0: Opening memory:
>> device_attach: ath0 attach returned 6
>>
>>
>> pciconf -lvc:
>>
>> ath0pci0:22:0:0:       class=0x020000
card=0x0a1014b7 chip=0x0013168c
>> rev=0x01 hdr=0x00
>>     vendor     = 'Atheros Communications Inc.'
>>     device     = 'AR5212, AR5213 802.11a/b/g
Wireless Adapter'
>>     class      = network
>>     subclass   = ethernet
>>
>>
============================================================

>> PROXIM Silver:
>>
============================================================

>>
>> info:
>>
>> Proxim SILVER 802.11a/b/g ComboCard
>> Model: 8481-WD
>> MAC-Address: 0020A64C713A
>> SN: 03MT21000304
>> P/N: 64738/A
>>
>> dmesg (verbose):
>>
>> pcib7: requested memory range
0x88000000-0xffffffff: good
>> cbb0: Opening memory:
>> cbb0: Normal: 0xbfeb0000-0xbfebffff
>> unknown: Lazy allocation of 0x10000 bytes rid 0x10
type 3 at 0xbfeb0000
>> cardbus0: Expecting link target, got 0x0
>> cbb0: Opening memory:
>>         map[10]: type Memory, range 32, base 0,
size 16, enabled
>> pcib7: requested memory range
0x88000000-0xffffffff: good
>> found-> vendor=0x168c, dev=0x0013, revid=0x01
>>         domain=0, bus=22, slot=0, func=0
>>         class=02-00-00, hdrtype=0x00, mfdev=0
>>         cmdreg=0x0002, statreg=0x0290, cachelnsz=0
(dwords)
>>         lattimer=0x00 (0 ns), mingnt=0x0a (2500
ns), maxlat=0x1c (7000 ns)
>>         intpin=a, irq=16
>>         powerspec 2  supports D0 D3  current D0
>> ath0: <Atheros 5212> mem
0xbfeb0000-0xbfebffff irq 16 at device 0.0 on
>> cardbus0
>> ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xbfeb0000
>> cbb0: Opening memory:
>> cbb0: Normal: 0xbfeb0000-0xbfebffff
>> ath0: [MPSAFE]
>> ath0: [ITHREAD]
>> ath0: unable to attach hardware; HAL status 13
>> cbb0: Opening memory:
>> device_attach: ath0 attach returned 6
>>
>> pciconf -lvc:
>>
>> ath0pci0:22:0:0:       class=0x020000
card=0xaa1014b7 chip=0x0013168c
>> rev=0x01 hdr=0x00
>>     vendor     = 'Atheros Communications Inc.'
>>     device     = 'AR5212, AR5213 802.11a/b/g
Wireless Adapter'
>>     class      = network
>>     subclass   = ethernet
>>     
>
>
>   

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Sam,

> laptop.  I happen to have a t61p and just tried a bunch
of different
> cards (including one w/ this device id) and all the
cards I expected to
> work so the best I can suggest is you try the card in
another laptop.

it really looks like there's something weird about the
PCCARD slot
in (my) T61p. I tried with an older T41p running
6.2-RELEASE-p4 and
the card successfully works, see the verbose dmesg excerpt
(complete
one is below my signature):

pcib2: cardbus0 requested memory range
0xc0200000-0xcfffffff: good
pcib2: cardbus0 requested memory range
0xc0200000-0xcfffffff: good
pcib2: cardbus0 requested memory range
0xc0240000-0xc024ffff: good
found->	vendor=0x168c, dev=0x0013, revid=0x01
	bus=3, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0xa8 (5040 ns), mingnt=0x0a (2500 ns), maxlat=0x1c
(7000
ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
ath0: <Atheros 5212> mem 0xc0240000-0xc024ffff irq 11
at device 0.0 on
cardbus0
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xc0240000
ath0: Reserved 0x1 bytes for rid 0 type 1 at 0xb
ath0: [MPSAFE]
ath0: bpf attached
ath0: Ethernet address: 00:20:a6:4c:71:3a
ath0: bpf attached
ath0: bpf attached
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps
48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps
12Mbps 18Mbps 24Mbps
36Mbps 48Mbps 54Mbps
ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps
48Mbps 54Mbps
ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons

So I assume it should work on 7.0 and the problem is
elsewhere...
any ideas on further debugging? Maybe if imp could
help with
this?

Thanks a lot,
Petr

============================================================
====
                            Petr Holub
CESNET z.s.p.o.                       Supercomputing Center
Brno
Zikova 4                             Institute of Compt.
Science
162 00 Praha 6, CZ                            Masaryk
University
Czech Republic                     Botanicka 68a, 60200
Brno, CZ 
e-mail: Petr.Holubcesnet.cz               phone:
+420-549493944
                                             fax:
+420-541212747
                                       e-mail: hopetics.muni.cz

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991,
1992, 1993, 1994
	The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD
Foundation.
FreeBSD 6.2-RELEASE-p4 #0: Thu Apr 26 17:55:55 UTC 2007
    rooti386-builder.daemonology.net:/usr/obj/usr/src/sys/SMP

Preloaded elf kernel "/boot/kernel/kernel" at
0xc0bab000.
Preloaded elf module "/boot/kernel/snd_ich.ko" at
0xc0bab19c.
Preloaded elf module "/boot/kernel/sound.ko" at
0xc0bab248.
Preloaded elf module "/boot/kernel/acpi_ibm.ko" at
0xc0bab2f4.
Preloaded elf module "/boot/kernel/acpi.ko" at
0xc0bab3a4.
Preloaded elf module "/boot/kernel/ng_ubt.ko" at
0xc0bab450.
Preloaded elf module "/boot/kernel/netgraph.ko" at
0xc0bab4fc.
Preloaded elf module "/boot/kernel/atapicam.ko" at
0xc0bab5ac.
Calibrating clock(s) ... i8254 clock: 1193148 Hz
CLK_USE_I8254_CALIBRATION not specified - using default
frequency
Timecounter "i8254" frequency 1193182 Hz quality
0
Calibrating TSC clock ... TSC clock: 1694510444 Hz
CPU: Intel(R) Pentium(R) M processor 1700MHz (1694.51-MHz
686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping =
5
 
Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MT
RR,PGE,MCA,CMOV,PAT
,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
  Features2=0x180<EST,TM2>
real memory  = 1609957376 (1535 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009dfff, 643072 bytes (157
pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768
pages)
0x0000000000c28000 - 0x000000005e416fff, 1568600064 bytes
(382959 pages)
avail memory = 1568276480 (1495 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f6d20
bios32: Entry = 0xfd750 (c00fd750)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xfd6e0+0x1f6
pnpbios: Found PnP BIOS data at 0xc00f6da0
pnpbios: Entry = f0000:b614  Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
ath_rate: version 1.2 <SampleRate bit-rate selection
algorithm>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112,
RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Apr 26 2007
17:55:39)
npx0: INT 16 interface
acpi0: <IBM TP-1R> on motherboard
acpi0: [MPSAFE]
acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port
0x62,0x66 on acpi0
pci_open(1):	mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there
(id=33408086)
pcibios: BIOS version 2.10
Found $PIR table, 15 entries at 0xc00fdea0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0    0    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0    0    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0    0    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0    2    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0    2    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0    1    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0    1    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    1    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    1    0    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    2    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    2    0    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    2    0    C   0x62  3 4 5 6 7 9 10 11 12 14 15
slot 1      2    2    A   0x62  3 4 5 6 7 9 10 11 12 14 15
slot 1      2    2    B   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    D   0x63  3 4 5 6 7 9 10 11 12 14 15
slot 2      9    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
slot 2      9    0    B   0x61  3 4 5 6 7 9 10 11 12 14 15
slot 2      9    0    C   0x62  3 4 5 6 7 9 10 11 12 14 15
slot 2      9    0    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    9    1    A   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    9    2    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    9    2    B   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2    1    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    2    8    A   0x68  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    B   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    D   0x6b  3 4 5 6 7 9 10 11 12 14 15
embedded    0   31    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   31    B   0x61  3 4 5 6 7 9 10 11 12 14 15
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 2 dev 0 func 0
AcpiOsDerivePciId: bus 2 dev 0 func 1
AcpiOsDerivePciId: bus 0 dev 29 func 7
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd970d000 pa 0x90000
atpic: Programming IRQ9 as level/low
ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 ->
10
Timecounter "ACPI-fast" frequency 3579545 Hz
quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port
0x1008-0x100b on acpi0
pci_link0: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link0: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link0: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link1: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link1: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link1: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link2: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link2: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link2: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link3: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link3: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link3: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link4: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link4: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link4: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link5: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link5: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link5: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link6: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link6: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link6: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
pci_link7: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link7: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11
pci_link7: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x1010
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on
acpi0
ACPI: Found matching pin for 0.29.INTA at func 0: 11
ACPI: Found matching pin for 0.29.INTB at func 1: 11
ACPI: Found matching pin for 0.29.INTC at func 2: 11
ACPI: Found matching pin for 0.29.INTD at func 7: 11
ACPI: Found matching pin for 0.31.INTA at func 1: 255
ACPI: Found matching pin for 0.31.INTB at func 3: 11
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found->	vendor=0x8086, dev=0x3340, revid=0x03
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	map[10]: type 3, range 32, base d0000000, size 28, enabled
found->	vendor=0x8086, dev=0x3341, revid=0x03
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
	lattimer=0x60 (2880 ns), mingnt=0x0c (3000 ns), maxlat=0x00
(0 ns)
found->	vendor=0x8086, dev=0x24c2, revid=0x01
	bus=0, slot=29, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=a, irq=11
	map[20]: type 4, range 32, base 00001800, size  5, enabled
pcib0: matched entry for 0.29.INTA (src \_SB_.LNKA:0)
pcib0: slot 29 INTA routed to irq 11 via \_SB_.LNKA
found->	vendor=0x8086, dev=0x24c4, revid=0x01
	bus=0, slot=29, func=1
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=b, irq=11
	map[20]: type 4, range 32, base 00001820, size  5, enabled
pcib0: matched entry for 0.29.INTB (src \_SB_.LNKD:0)
pcib0: slot 29 INTB routed to irq 11 via \_SB_.LNKD
found->	vendor=0x8086, dev=0x24c7, revid=0x01
	bus=0, slot=29, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=c, irq=11
	map[20]: type 4, range 32, base 00001840, size  5, enabled
pcib0: matched entry for 0.29.INTC (src \_SB_.LNKC:0)
pcib0: slot 29 INTC routed to irq 11 via \_SB_.LNKC
found->	vendor=0x8086, dev=0x24cd, revid=0x01
	bus=0, slot=29, func=7
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=d, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type 1, range 32, base c0000000, size 10, enabled
pcib0: matched entry for 0.29.INTD (src \_SB_.LNKH:0)
pcib0: slot 29 INTD routed to irq 11 via \_SB_.LNKH
found->	vendor=0x8086, dev=0x2448, revid=0x81
	bus=0, slot=30, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x8080, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0
ns)
found->	vendor=0x8086, dev=0x24cc, revid=0x01
	bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
found->	vendor=0x8086, dev=0x24ca, revid=0x01
	bus=0, slot=31, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=a, irq=255
	map[20]: type 4, range 32, base 00001860, size  4, enabled
	map[24]: type 1, range 32, base 00000000, size 10, memory
disabled
found->	vendor=0x8086, dev=0x24c3, revid=0x01
	bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=b, irq=11
	map[20]: type 4, range 32, base 00001880, size  5, enabled
pcib0: matched entry for 0.31.INTB (src \_SB_.LNKB:0)
pcib0: slot 31 INTB routed to irq 11 via \_SB_.LNKB
found->	vendor=0x8086, dev=0x24c5, revid=0x01
	bus=0, slot=31, func=5
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00001c00, size  8, enabled
	map[14]: type 4, range 32, base 000018c0, size  6, enabled
	map[18]: type 1, range 32, base c0000c00, size  9, enabled
	map[1c]: type 1, range 32, base c0000800, size  8, enabled
pcib0: matched entry for 0.31.INTB (src \_SB_.LNKB:0)
pcib0: slot 31 INTB routed to irq 11 via \_SB_.LNKB
found->	vendor=0x8086, dev=0x24c6, revid=0x01
	bus=0, slot=31, func=6
	class=07-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00002400, size  8, enabled
	map[14]: type 4, range 32, base 00002000, size  7, enabled
pcib0: matched entry for 0.31.INTB (src \_SB_.LNKB:0)
pcib0: slot 31 INTB routed to irq 11 via \_SB_.LNKB
agp0: <Intel 82855 host to AGP bridge> mem
0xd0000000-0xdfffffff at device
0.0 on pci0
agp0: Reserved 0x10000000 bytes for rid 0x10 type 3 at
0xd0000000
agp0: allocating GATT for aperture of size 256M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x3000-0x3fff
pcib1:   memory decode     0xc0100000-0xc01fffff
pcib1:   prefetched decode 0xe0000000-0xe7ffffff
ACPI: Found matching pin for 1.0.INTA at func 0: 11
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found->	vendor=0x1002, dev=0x4e54, revid=0x80
	bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0307, statreg=0x02b0, cachelnsz=8 (dwords)
	lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00
(0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 3, range 32, base e0000000, size 27, enabled
pcib1: (null) requested memory range 0xe0000000-0xe7ffffff:
good
	map[14]: type 4, range 32, base 00003000, size  8, enabled
pcib1: (null) requested I/O range 0x3000-0x30ff: in range
	map[18]: type 1, range 32, base c0100000, size 16, enabled
pcib1: (null) requested memory range 0xc0100000-0xc010ffff:
good
pcib1: matched entry for 1.0.INTA (src \_SB_.LNKA:0)
pcib1: slot 0 INTA routed to irq 11 via \_SB_.LNKA
pci1: <display, VGA> at device 0.0 (no driver
attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A>
port 0x1800-0x181f irq 11
at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1800
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on
uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr
1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B>
port 0x1820-0x183f irq 11
at device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1820
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on
uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr
1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C>
port 0x1840-0x185f irq 11
at device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1840
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on
uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr
1
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller>
mem
0xc0000000-0xc00003ff irq 11 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at
0xc0000000
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on
ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr
1
uhub3: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   8
pcib2:   I/O decode        0x4000-0x8fff
pcib2:   memory decode     0xc0200000-0xcfffffff
pcib2:   prefetched decode 0xe8000000-0xefffffff
pcib2:   Subtractively decoded bridge.
ACPI: Found matching pin for 2.0.INTA at func 0: 11
ACPI: Found matching pin for 2.0.INTB at func 1: 11
ACPI: Found matching pin for 2.1.INTA at func 0: 11
ACPI: Found matching pin for 2.2.INTA at func 0: 11
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found->	vendor=0x104c, dev=0xac46, revid=0x01
	bus=2, slot=0, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0107, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns),
maxlat=0x03 (750
ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base b0000000, size 12, enabled
pcib2: (null) requested memory range 0xb0000000-0xb0000fff:
good
pcib2: matched entry for 2.0.INTA (src \_SB_.LNKA:0)
pcib2: slot 0 INTA routed to irq 11 via \_SB_.LNKA
found->	vendor=0x104c, dev=0xac46, revid=0x01
	bus=2, slot=0, func=1
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0107, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns),
maxlat=0x03 (750
ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base b1000000, size 12, enabled
pcib2: (null) requested memory range 0xb1000000-0xb1000fff:
good
pcib2: matched entry for 2.0.INTB (src \_SB_.LNKB:0)
pcib2: slot 0 INTB routed to irq 11 via \_SB_.LNKB
found->	vendor=0x8086, dev=0x101e, revid=0x03
	bus=2, slot=1, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns),
maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type 1, range 32, base c0220000, size 17, enabled
pcib2: (null) requested memory range 0xc0220000-0xc023ffff:
good
	map[14]: type 1, range 32, base c0200000, size 16, enabled
pcib2: (null) requested memory range 0xc0200000-0xc020ffff:
good
	map[18]: type 4, range 32, base 00008000, size  6, enabled
pcib2: (null) requested I/O range 0x8000-0x803f: in range
pcib2: matched entry for 2.1.INTA (src \_SB_.LNKA:0)
pcib2: slot 1 INTA routed to irq 11 via \_SB_.LNKA
found->	vendor=0x8086, dev=0x1043, revid=0x04
	bus=2, slot=2, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x22
(8500 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type 1, range 32, base c0214000, size 12, enabled
pcib2: (null) requested memory range 0xc0214000-0xc0214fff:
good
pcib2: matched entry for 2.2.INTA (src \_SB_.LNKC:0)
pcib2: slot 2 INTA routed to irq 11 via \_SB_.LNKC
cbb0: <PCI-CardBus Bridge> mem 0xb0000000-0xb0000fff
irq 11 at device 0.0 on
pci2
cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at
0xb0000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
  0x00: 0xac46104c 0x02100107 0x06070001 0x00824008 
  0x10: 0xb0000000 0x220000a0 0xb0050302 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 
  0x40: 0x05521014 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x0840f071 0x040a0000 0x000f0000 0x01d21b22 
  0x90: 0x416422c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
cbb1: <PCI-CardBus Bridge> mem 0xb1000000-0xb1000fff
irq 11 at device 0.1 on
pci2
cbb1: Reserved 0x1000 bytes for rid 0x10 type 3 at
0xb1000000
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
  0x00: 0xac46104c 0x02100107 0x06070001 0x00824008 
  0x10: 0xb1000000 0x020000a0 0xb0080602 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740020b 
  0x40: 0x05521014 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x0840d071 0x040a0000 0x000f0000 0x01d21b22 
  0x90: 0x416422c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
em0: <Intel(R) PRO/1000 Network Connection Version -
6.2.9> port
0x8000-0x803f mem
0xc0220000-0xc023ffff,0xc0200000-0xc020ffff irq 11 at
device 1.0 on pci2
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at
0xc0220000
em0: Reserved 0x40 bytes for rid 0x18 type 4 at 0x8000
em0: bpf attached
em0: Ethernet address: 00:0d:60:d0:e5:27
em0: [MPSAFE]
pci2: <network> at device 2.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device
31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1860
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00
devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=51 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00
devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver
attached)
pcm0: <Intel ICH4 (82801DB)> port
0x1c00-0x1cff,0x18c0-0x18ff mem
0xc0000c00-0xc0000dff,0xc0000800-0xc00008ff irq 11 at device
31.5 on pci0
pcm0: Reserved 0x200 bytes for rid 0x18 type 3 at
0xc0000c00
pcm0: Reserved 0x100 bytes for rid 0x1c type 3 at
0xc0000800
pcm0: [MPSAFE]
pcm0: <Analog Devices AD1981B AC97 Codec (id =
0x41445374)>
pcm0: Codec features headphone, 20 bit DAC, 5 bit master
volume, no 3D
Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM,
AMAP, reserved 4
pcm0: ac97 codec dac ready count: 0
pcm0: sndbuf_setmap 5e057000, 4000; 0xf5e26000 ->
5e057000
pcm0: sndbuf_setmap 5e053000, 4000; 0xf5e2a000 ->
5e053000
pci0: <simple comms, generic modem> at device 31.6 (no
driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64
irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x54ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> flags 0x2000 irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00002000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
fdc0: <floppy drive controller (FDE)> port
0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x201 0x201 0x201 0x201
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff
irq 4 flags 0x10 on
acpi0
sio0: type 8250 or not responding
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Standard parallel printer port> port
0x3bc-0x3be irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1: probe failed test(s): 0 1 2 4 6 7 9
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_ibm0: <IBM ThinkPad ACPI Extras> on acpi0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1: probe failed test(s): 0 1 2 4 6 7 9
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ahc_isa_probe 1: ioport 0x1c00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcffff,0xd0000-0xd0fff,0xd1000-0xd1fff,0xdc000-0xdf
fff,0xe0000-0xef
fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 102135 -> 100000
procfs registered
Timecounter "TSC" frequency 1694510444 Hz quality
800
Timecounters tick every 1.000 msec
lo0: bpf attached
rr232x: no controller detected.
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
battery0: battery initialization start
acpi_acad0: acline initialization start
battery0: battery initialization done, tried 1 times
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on ICH4 chip
ad0: setting UDMA100 on ICH4 chip
ad0: 53959MB <HTS726060M9AT00 MH4OA6BA> at ata0-master
UDMA100
ad0: 110509426 sectors [109632C/16H/63S] 16
sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire
acd0: setting PIO4 on ICH4 chip
acd0: setting UDMA33 on ICH4 chip
acd0: <TOSHIBA DVD-ROM SD-R9012/1121> CDRW drive at
ata1 as master
acd0: read 4134KB/s (4134KB/s) write 2755KB/s (2755KB/s),
2048KB buffer,
UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM,
packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
pcm0: measured ac97 link rate at 47999 Hz, will use 48000
Hz
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
pass0 at ata1 bus 0 target 0 lun 0
pass0: <TOSHIBA DVD-ROM SD-R9012 1121> Removable
CD-ROM SCSI-0 device 
pass0: 33.000MB/s transfers
GEOM: new disk cd0
ATA PseudoRAID loaded
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TOSHIBA DVD-ROM SD-R9012 1121> Removable CD-ROM
SCSI-0 device 
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium
not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
Linux ELF exec handler installed
pcib2: cardbus0 requested memory range
0xc0200000-0xcfffffff: good
pcib2: cardbus0 requested memory range
0xc0200000-0xcfffffff: good
pcib2: cardbus0 requested memory range
0xc0240000-0xc024ffff: good
found->	vendor=0x168c, dev=0x0013, revid=0x01
	bus=3, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0xa8 (5040 ns), mingnt=0x0a (2500 ns), maxlat=0x1c
(7000
ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
ath0: <Atheros 5212> mem 0xc0240000-0xc024ffff irq 11
at device 0.0 on
cardbus0
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at
0xc0240000
ath0: Reserved 0x1 bytes for rid 0 type 1 at 0xb
ath0: [MPSAFE]
ath0: bpf attached
ath0: Ethernet address: 00:20:a6:4c:71:3a
ath0: bpf attached
ath0: bpf attached
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps
48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps
12Mbps 18Mbps 24Mbps
36Mbps 48Mbps 54Mbps
ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps
48Mbps 54Mbps
ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

> broken with the PCCARD slot rather than the card. Can
that be
> because it's dual PCMCIA/ExpressCard slot? Any hints
for further
> debugging of the problem?

I've just tried the following, if it is of any help:

[rootkloboucek ~]# sysctl -a | fgrep -i cardbus
hw.cardbus.cis_debug: 0
hw.cardbus.debug: 0
dev.cbb.0.%desc: RF5C476 PCI-CardBus Bridge
dev.cardbus.%parent: pci
dev.cardbus.0.%desc: CardBus bus
dev.cardbus.0.%driver: cardbus
dev.cardbus.0.%parent: cbb0
[rootkloboucek ~]# sysctl -w hw.cardbus.cis_debug=1
hw.cardbus.cis_debug: 0 -> 1
[rootkloboucek ~]# sysctl -w hw.cardbus.debug=1
hw.cardbus.debug: 0 -> 1
[rootkloboucek ~]# 
cardbus0: CIS pointer is 0x5001
cardbus0: CIS in BAR 0x10
cardbus0: Expecting link target, got 0x0
cardbus0: Warning: Bogus CIS ignored
ath0: <Atheros 5212> mem 0xbfeb0000-0xbfebffff irq 16
at device 0.0 on
cardbus0
ath0: [ITHREAD]
ath0: unable to attach hardware; HAL status 13
device_attach: ath0 attach returned 6

Petr

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"

Sam,

I did a test on T61p with FreeSBIE 2.0.1 (i.e. FreeBSD
6.2-RELEASE)
and when plugged in, the driver return the same HAL 13
problem as
with 7.0-RELEASE. Given the fact that the same card works
on
6.2-RELEASE on T41p laptop, my conclusion is there's
something
broken with the PCCARD slot rather than the card. Can that
be
because it's dual PCMCIA/ExpressCard slot? Any hints for
further
debugging of the problem?

TIA,
Petr

_______________________________________________
freebsd-hardwarefreebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hard
ware
To unsubscribe, send any mail to
"freebsd-hardware-unsubscribefreebsd.org"