helix on S60 3.2

 

-----Original Message-----
From: ext eluevanodextratech.com [mailto:eluevanodextratech.com] 
Sent: Monday, August 20, 2007 3:21 PM
To: Gupta Ashish.As (Nokia-TP-MSW/Dallas)
Cc: clientapps-dev-bounceshelixcommunity.org;
datatype-devhelixcommunity.org; xiyangti.com;
clientapps-devhelixcommunity.org
Subject: RE: [Clientapps-dev] helix on S60 3.2

Hello Ashish,
Thank you for the reply.
I'm working at Texas Instruments and I have access to  a
licensed SDK
from Nokia, so I will use SymbianMmf, I had a doubt because
I saw that
in some CR emails the target SymbianMmf_rel is mentioned.
Which differences are between SymbianMmf_rel and
SymbianMmf?
<Ashish> SymbianMmf_rel and SymbainMmf are more or
less same. You can
use SymbianMmf_rel which doesn't build some extra codecs
(e.g. MP3)
which are not required.

What about functionality of the
helix-client-s60-32-mmf-mdf-dsp profile?
I want to run helix with dsp codecs.

<Ashish> Yes that would be the correct profile for
DSP.

Thanks and Regards
Edgar Luevano



>
> Hi,
>
> 210_Cays
> symbianplay/SymbianMmf depending on the target and SDK
used. If 
> building with public SDK, it would be better to use
symbianplay.
> helix-client-s60-32-mmf-mdf-arm
>
> Thanks
> Ashish
>
>
> -----Original Message-----
> From: clientapps-dev-bounceshelixcommunity.org
> [mailto:clientapps-dev-bounceshelixcommunity.org]
> Sent: Friday, August 17, 2007 4:05 PM
> To: datatype-devhelixcommunity.org
> Cc: xiyangti.com; clientapps-devhelixcommunity.org
> Subject: [Clientapps-dev] helix on S60 3.2
>
> Hello all,
> I would like to know which combination of
branch/target/profile should

> I use for S60 3.2?
> Thanks and Regards
> Edgar Luevano
>
>
> _______________________________________________
> Clientapps-dev mailing list
> Clientapps-devhelixcommunity.org
> http://lists.helixcommunity.org/mailman/listinfo/
clientapps-dev
>
> _______________________________________________
> Clientapps-dev mailing list
> Clientapps-devhelixcommunity.org
> http://lists.helixcommunity.org/mailman/listinfo/
clientapps-dev
>



_______________________________________________
Datatype-dev mailing list
Datatype-devhelixcommunity.org
http://lists.helixcommunity.org/mailman/listinfo/da
tatype-dev

Hello Ashish,
I want to ask you about something that happens in the
beginning of the
video playback.

In the beginning of the playback I can observe that the
frames freeze for
a small period of time, and then continue being displayed
normally.

Observing the logs (attached) I saw two different reasons
for this to happen.

- For mpeg4 playback (AAC and AMR-NB), video and audio
starts playing
about the same time, but after a few audio buffers are
decoded, they stop
being decoded and the samples played keep the same value for
some time.
However the video continue being displayed and the
clocksource
continue increasing. then audio continues being decoded, and
the
clocksource synchronize with samples played, but because the
frames video
continued being displayed following the clocksource, and the
clocksource
value is now smaller (sync to samples played that kept
without
modification
for some time), the video frames waits to the audio to reach
the video time.


-For h263 playback (AAC and AMR-NB), Audio starts later, and
when starting
synchronize clocksource having the same effect that in mpeg4
(new frames
are not
displayed because now the clocksource value is smaller).


Have you seen this behavior before? Do you have an idea of
what can be the
reason for  this behaviour in audio?

Thanks and Regards
Edgar

_______________________________________________
Datatype-dev mailing list
Datatype-devhelixcommunity.org
http://lists.helixcommunity.org/mailman/listinfo/da
tatype-dev