Gorkem,
I thought I HAD followed all of the instructions in the userguide FAQ,
please could you let me know what it is that I'm missing out from there ?
Thanks
Peter
--- In IQWFServer%40yahoogroups.com">IQWFServer
yahoogroups.com, "Fastream Technologies" <gates...>
wrote:
>
> Please follow the instructions on the user guide FAQ about manual
passive
> mode.
>
> Regards,
>
> Gorkem Ates
>;
>
> On 10/21/07, peter.talboys <peter.talboys...> wrote:
> >
>; > Hi,
> > I'm new to setting up the FTP server stuff, as far as I can tell I've
>; > set everything up as the userguide tells me, but I'm getting the
> > following errors when connecting to my FTP server when using the
> > external IP address, all works fine when using the LAN address. I'm
> > assuming I have not set up the passthrough ports properly on my
> > router, but I can't see how to set up more than one port to go through
> > to one internal address, I can't seem to set up ranges of ports to go
> > through to my FTP server. I'm running a D-link DI634M if that
helps any ?
> >
>; > thanks
> > Peter
> > *** CuteFTP 8.0 - build May 31 2007 ***
> >
>; > STATUS:>; [20/10/2007 22:51:16] Getting listing ""...
>; > STATUS:>; [20/10/2007 22:51:16] Connecting to FTP server...
> > xx.xx.xx.xx:21 (ip = xx.xx.xx.xx)...
> > STATUS:>; [20/10/2007 22:51:16] Socket connected. Waiting for welcome
> > message...
> > [20/10/2007 22:51:16] 220 xxxxxx FTP Server
> > STATUS:>; [20/10/2007 22:51:16] Connected. Authenticating...
> > COMMAND:> [20/10/2007 22:51:16] USER xxx
> > [20/10/2007 22:51:16] 331 Password required for xxx.
>; > COMMAND:> [20/10/2007 22:51:16] PASS *****
> > [20/10/2007 22:51:16] 230 User xxx has successfully logged in.
> > STATUS:>; [20/10/2007 22:51:16] Login successful.
> > COMMAND:> [20/10/2007 22:51:16] PWD
> > [20/10/2007 22:51:16] 257 "/" is current directory.
> > STATUS:>; [20/10/2007 22:51:16] Home directory: /
> > COMMAND:> [20/10/2007 22:51:16] FEAT
>; > [20/10/2007 22:51:16] Informational Message Only:
> > 211-Extensions supported:
> > SIZE
>; > REST STREAM
> > PASV
>; > MDTM
>; > MDTM YYYYMMDDHHMMSS[+-TZ] filename
> > MLST size*;type*;perm*;create*;modify*;
> > MODE Z
> > MD5
> > AUTH
>; > PROT
>; > CCC
> > PBSZ
>; > CHPWD
> > 211 END
> > STATUS:>; [20/10/2007 22:51:16] This site supports features.
> > STATUS:>; [20/10/2007 22:51:16] This site supports SIZE.
> > STATUS:>; [20/10/2007 22:51:16] This site can resume broken downloads.
> > COMMAND:> [20/10/2007 22:51:16] MODE Z
> > [20/10/2007 22:51:16] 200 MODE Ok
> > COMMAND:> [20/10/2007 22:51:16] REST 0
> > [20/10/2007 22:51:16] 350 REST supported. Ready to resume at byte
>; > offset 0.
> > COMMAND:> [20/10/2007 22:51:16] PASV
>; > [20/10/2007 22:51:16] 227 Entering Passive Mode
(xxx.xxx.x.xxx,19,137).
> > STATUS:>; [20/10/2007 22:51:16] Substituting received PASV address
> > xxx.xxx.x.xxx to server address xx.xx.xxx.xxx.
> > COMMAND:> [20/10/2007 22:51:16] LIST
>; > STATUS:>; [20/10/2007 22:51:16] Connecting FTP data socket...
> > xx.xx.xxx.xxx:5001...
> > ERROR:> [20/10/2007 22:51:17] The remote host actively refused the
> > attempt to connect to it.
> > 1) Verify that the destination server name or IP address is correct
> > 2) Verify that the connection port number is correct (under Site
>; > Settings | Type tab).
> > 3) The remote server may be temporarily or permanently inaccessible
> > (try again later).
> > 4) Verify that you have chosen the right protocol (SSH2, SSL, FTP,
>; > etc.) and have setup all required options for that protocol.
> > 5) Verify that the destination IP address and port numbers are
correct.
> > 6) The remote server may be refusing multiple connections from the
> > same client. Try using only one connection thread when connecting to
> > this particular server (Site Settings | Options).
> > 7) Try pinging the address.
> > 8) If you are using a router, verify the router is up and running
> > (check by pinging it and then ping an address outside of the router).
> > 9) Do a traceroute to the destination to verify all routers along
> > the connection path are operational.
> > 10) Verify that your subnet mask is setup properly.
> > 11) Verify that your local software or hardware firewall is not
> > blocking outbound connections originating from CuteFTP.
> > 12) Verify that your anti-virus software is not at fault (try
>; > disabling it).
>; > ERROR:> [20/10/2007 22:51:17] PASV failed, trying PORT.
> > STATUS:>; [20/10/2007 22:51:17] Waiting 0 seconds...
> > STATUS:>; [20/10/2007 22:51:18] Getting listing "/"...
> > STATUS:>; [20/10/2007 22:51:18] Connecting to FTP server...
> > xx.xx.xxx.xxx:21 (ip = xx.xx.xxx.xxx)...
> > STATUS:>; [20/10/2007 22:51:18] Socket connected. Waiting for welcome
> > message...
> > [20/10/2007 22:51:18] 220 xxxxx FTP Server
> > STATUS:>; [20/10/2007 22:51:18] Connected. Authenticating...
> > COMMAND:> [20/10/2007 22:51:18] USER xxx
> > [20/10/2007 22:51:18] 331 Password required for xxx.
>; > COMMAND:> [20/10/2007 22:51:18] PASS *****
> > [20/10/2007 22:51:18] 230 User xxx has successfully logged in.
