|
List Info
Thread: PE-4FE-TX not transmitting anything...faulty?
|
|
| PE-4FE-TX not transmitting
anything...faulty? |
 
Germany |
2007-04-16 15:48:58 |
Hello,
i've got a PE-4FE-TX here which is not working, it is
receiving traffic
but not transmitting anything.
See below:
MAC statistics: Receive
Transmit
Total octets 26985313
0
Total packets 419556
0
Unicast packets 1458
0
Broadcast packets 411000
0
Multicast packets 7098
0
CRC/Align errors 0
0
FIFO errors 0
0
MAC control frames 0
0
MAC pause frames 0
0
Oversized frames 0
Jabber frames 0
Fragment frames 0
VLAN tagged frames 0
Code violations 0
Filter statistics:
Input packet count 419556
Input packet rejects 0
Input DA rejects 8556
Input SA rejects 0
Output packet count
0
Output packet pad count
0
Output packet error count
0
CAM destination filters: 1, CAM source filters: 0
I've tried everything to get this pic to send out
anything...
It seems it does receive packets but its not transmitting
anything. It
doesnt matter what port i use, none works.
I've tried various devices, duplex/speed settings, tried the
PIC in
various FPCs and even in various M-series.
Does anyone have any idea how i can debug this further or
did anyone
happen to run into the same problem?
Regards,
Jonas Frey
_______________________________________________
juniper-nsp mailing list juniper-nsp puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
|
|
| Re: PE-4FE-TX not transmitting
anything...faulty? |
Germany |
2007-04-16 16:43:09 |
Ebben,
it sounds related but i am not sure if it really is.
When i run monitor traffic interface fe...
i do see incoming packets and i do see that the interface is
(trying to)
transmitting arp replys:
23:37:47.921802 Out arp reply x.x.x.x is-at
0:90:69:53:79:1b
However this does never arrive at the remote station nor
does it
increase the transmit packet counter. It seems the software
is doing
everything it should but the hardware is (silently) dropping
the
packets.
I also do not have "drops" on the interface:
Input errors:
Errors: 0, Drops: 0, Framing errors: 0, Runts: 0,
Policed discards:
9822, L3 incompletes: 682, L2 channel errors: 0, L2 mismatch
timeouts:
0, FIFO errors: 0,
Resource errors: 0
Output errors:
Carrier transitions: 3, Errors: 0, Drops: 0, Collisions:
0, Aged
packets: 0, FIFO errors: 0, HS link CRC errors: 0, MTU
errors: 0,
Resource errors: 0
Queue counters: Queued packets Transmitted packets
Dropped
packets
0 best-effort 150 150
0
1 expedited-fo 0 0
0
2 assured-forw 0 0
0
3 network-cont 0 0
0
As you can see...the queue counters say there has been
something
transmitted but on the other hands the MAC says it didnt:
MAC statistics: Receive
Transmit
Total octets 32422297
0
Total packets 504050
0
Unicast packets 1811
0
Broadcast packets 493497
0
Multicast packets 8742
0
CRC/Align errors 0
0
FIFO errors 0
0
MAC control frames 0
0
MAC pause frames 0
0
Very strange....
Regarding your problem: I bet cycling (request... off/on)
the pic will
do the job.
Regards,
Jonas
On Mon, 2007-04-16 at 23:30, Ebben Aries wrote:
> I have ran into this regarding my post on 3/29.
Attached is a copy of the
> thread.
>
> My problem however was only with 1 port on the
P-4FE-TX. I have not had the
> chance to power cycle the PIC or swap into a different
FPC as of yet. Are
> you seeing the drop counters increase at all or just no
traffic sent at all?
> Also, are you seeing any RE bound traffic attempting to
be sent when you
> issue 'monitor traffic interface fe-x/x/x' ?
>
> Anyone else out there ran into this? I am also
anxiously awaiting any
> insight.
>
> Thanks,
>
> Ebben
>
>
> ----
>
> From:
> Ebben Aries <eariesuci.net> (United
Communications, Inc.)
> To:
> juniper-nsppuck.nether.net
> Date:
> 2007-03-29 1:09 pm
>
> Hello all,
>
> This is a weird one...... I have a P-4FE-TX that has
one interface that is
> displaying the following.
>
> Output errors:
> Carrier transitions: 0, Errors: 0, Drops: 29052,
Collisions: 0, Aged
> packets: 0, FIFO errors: 0, HS link CRC errors: 0, MTU
errors: 0, Resource
> errors: 0
> Egress queues: 4 supported, 4 in use
> Queue counters: Queued packets Transmitted
packets Dropped packets
> 0 best-effort 3278 0
0
> 1 expedited-forwarding 0 0
0
> 2 assured-forwarding 0 0
0
> 3 network-control 29782 0
29052
>
> This is strictly a p2p ethernet link that was working
until the
> following...... This interface was put into an 802.3ad
bundle attached to
> ae0.0 (this is when it started to drop everything).
The interface was then
> removed and now displays the above.
>
> It appears that BE is neither transmitting nor dropping
the packets while
> network-control is dropping virtualy everything. The
interface can RX
> traffic just fine.
>
> BTW, other interfaces on the same P-4FE-TX work fine
and there are no firewall
> filters attached to this interface.
>
> Anyone ran into this before ??
>
> --
>
> Ebben
>
>
>
>
> On Monday 16 April 2007 1:48 pm, Jonas Frey wrote:
> > Hello,
> >
> > i've got a PE-4FE-TX here which is not working, it
is receiving traffic
> > but not transmitting anything.
> > See below:
> > MAC statistics: Receive
Transmit
> > Total octets 26985313
0
> > Total packets 419556
0
> > Unicast packets 1458
0
> > Broadcast packets 411000
0
> > Multicast packets 7098
0
> > CRC/Align errors 0
0
> > FIFO errors 0
0
> > MAC control frames 0
0
> > MAC pause frames 0
0
> > Oversized frames 0
> > Jabber frames 0
> > Fragment frames 0
> > VLAN tagged frames 0
> > Code violations 0
> > Filter statistics:
> > Input packet count 419556
> > Input packet rejects 0
> > Input DA rejects 8556
> > Input SA rejects 0
> > Output packet count
0
> > Output packet pad count
0
> > Output packet error count
0
> > CAM destination filters: 1, CAM source
filters: 0
> >
> > I've tried everything to get this pic to send out
anything...
> > It seems it does receive packets but its not
transmitting anything. It
> > doesnt matter what port i use, none works.
> >
> > I've tried various devices, duplex/speed settings,
tried the PIC in
> > various FPCs and even in various M-series.
> >
> > Does anyone have any idea how i can debug this
further or did anyone
> > happen to run into the same problem?
> >
> > Regards,
> > Jonas Frey
> >
> > _______________________________________________
> > juniper-nsp mailing list juniper-nsppuck.nether.net
> >
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list juniper-nsppuck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
|
|
| Re: PE-4FE-TX not transmitting
anything...faulty? |
 
United States |
2007-04-16 16:30:01 |
I have ran into this regarding my post on 3/29. Attached is
a copy of the
thread.
My problem however was only with 1 port on the P-4FE-TX. I
have not had the
chance to power cycle the PIC or swap into a different FPC
as of yet. Are
you seeing the drop counters increase at all or just no
traffic sent at all?
Also, are you seeing any RE bound traffic attempting to be
sent when you
issue 'monitor traffic interface fe-x/x/x' ?
Anyone else out there ran into this? I am also anxiously
awaiting any
insight.
Thanks,
Ebben
----
From:
Ebben Aries <eariesuci.net> (United Communications,
Inc.)
To:
juniper-nsppuck.nether.net
Date:
2007-03-29 1:09 pm
Hello all,
This is a weird one...... I have a P-4FE-TX that has one
interface that is
displaying the following.
Output errors:
Carrier transitions: 0, Errors: 0, Drops: 29052,
Collisions: 0, Aged
packets: 0, FIFO errors: 0, HS link CRC errors: 0, MTU
errors: 0, Resource
errors: 0
Egress queues: 4 supported, 4 in use
Queue counters: Queued packets Transmitted packets
Dropped packets
0 best-effort 3278 0
0
1 expedited-forwarding 0 0
0
2 assured-forwarding 0 0
0
3 network-control 29782 0
29052
This is strictly a p2p ethernet link that was working until
the
following...... This interface was put into an 802.3ad
bundle attached to
ae0.0 (this is when it started to drop everything). The
interface was then
removed and now displays the above.
It appears that BE is neither transmitting nor dropping the
packets while
network-control is dropping virtualy everything. The
interface can RX
traffic just fine.
BTW, other interfaces on the same P-4FE-TX work fine and
there are no firewall
filters attached to this interface.
Anyone ran into this before ??
--
Ebben
On Monday 16 April 2007 1:48 pm, Jonas Frey wrote:
> Hello,
>
> i've got a PE-4FE-TX here which is not working, it is
receiving traffic
> but not transmitting anything.
> See below:
> MAC statistics: Receive
Transmit
> Total octets 26985313
0
> Total packets 419556
0
> Unicast packets 1458
0
> Broadcast packets 411000
0
> Multicast packets 7098
0
> CRC/Align errors 0
0
> FIFO errors 0
0
> MAC control frames 0
0
> MAC pause frames 0
0
> Oversized frames 0
> Jabber frames 0
> Fragment frames 0
> VLAN tagged frames 0
> Code violations 0
> Filter statistics:
> Input packet count 419556
> Input packet rejects 0
> Input DA rejects 8556
> Input SA rejects 0
> Output packet count
0
> Output packet pad count
0
> Output packet error count
0
> CAM destination filters: 1, CAM source filters: 0
>
> I've tried everything to get this pic to send out
anything...
> It seems it does receive packets but its not
transmitting anything. It
> doesnt matter what port i use, none works.
>
> I've tried various devices, duplex/speed settings,
tried the PIC in
> various FPCs and even in various M-series.
>
> Does anyone have any idea how i can debug this further
or did anyone
> happen to run into the same problem?
>
> Regards,
> Jonas Frey
>
> _______________________________________________
> juniper-nsp mailing list juniper-nsppuck.nether.net
>
https://puck.nether.net/mailman/listinfo/juniper-nsp
--
Ebben Aries
Lead Network Engineer
United Communications, Inc.
389 SW Scalehouse Ct. Suite 100
Bend, OR 97702
Office: 541.322.1407
Fax: 541.322.1417
eariesuci.net
_______________________________________________
juniper-nsp mailing list juniper-nsppuck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp
|
|
[1-3]
|
|