BSC/RNC Identifier

Hello,

I didn't find in the specification how was identified a
BSC/RNC in Megaco. When the MGC sends a request to a MGW, we
know which MGW it is by looking at the message ID. But is it
possible to know for which BSC/RNC connected to the MGW it
is meant?
Is there an identifier for each BSC connected to the MGW in
Megaco?

Thanks for your help.
Joseph Verrière

------------------------------------------------------------
----------------------------------------

Ce message et tout document joint sont confidentiels et à
l'intention exclusive des destinataires. S'ils vous ont été
adressés par erreur, merci d'en informer immédiatement
l'expéditeur et de les détruire. Toute copie, diffusion ou
utilisation non autorisée est interdite. Tout message
électronique est susceptible d'altération : Astellia décline
toute responsabilité si le message ou les documents joints
ont subi une quelconque modification.

This message and any attachment are confidential and
intended solely to its addressees. If you are not the
intended recipient please cancel it and inform immediately
the sender. Any unauthorised copy or dissemination is
prohibited. Electronic messages may be altered: Astellia
shall not be liable for those circumstances.

------------------------------------------------------------
----------------------------------------



_______________________________________________
Megaco mailing list
Megacoietf.org
https:/
/www1.ietf.org/mailman/listinfo/megaco

The network elements itself are not identified, it's rather
the "interface"
between the CS-MGW and the BSC/RNC.
This is related to the bearer connection endpoint in the
MGW, thus the
indication is done via H.248 TerminationID.

E.g. 1: BSC -> A reference point -> TDM bearer
connection -> TerminationID
for the H.248 physical termination (no bearer control
protocol)
E.g. 2: RNC -> Iu-cs reference point -> AAL2 or IP
bearer connection ->
TerminationID for the H.248 ephemeral termination (+ ALCAP
as bearer
control protocol)

Please note that the subject you are questioning is NOT
specific to BSC/RNC
nodes, this is actually general to all node types which are
peered (via
connection-oriented bearer technologies) by an H.248 MGW
(like a local or
transit exchange, PABX, access node, etc etc).

-Albrecht



                                                            
                                                            
           
                      "Verriere                        
                                                            
                
                      Joseph"                  To:     
<megacoietf.org>                                         
                  
                      <j.verriereaste         cc:           
                                                            
          
                      llia.com>                Subject:
[Megaco] BSC/RNC Identifier                                 
                
                                                            
                                                            
           
                      20.03.2007 11:57                      
                                                            
           
                                                            
                                                            
           




Hello,

I didn't find in the specification how was identified a
BSC/RNC in Megaco.
When the MGC sends a request to a MGW, we know which MGW it
is by looking
at the message ID. But is it possible to know for which
BSC/RNC connected
to the MGW it is meant?
Is there an identifier for each BSC connected to the MGW in
Megaco?

Thanks for your help.
Joseph Verrière

------------------------------------------------------------
----------------------------------------


Ce message et tout document joint sont confidentiels et à
l'intention
exclusive des destinataires. S'ils vous ont été adressés par
erreur, merci
d'en informer immédiatement l'expéditeur et de les détruire.
Toute copie,
diffusion ou utilisation non autorisée est interdite. Tout
message
électronique est susceptible d'altération : Astellia décline
toute
responsabilité si le message ou les documents joints ont
subi une
quelconque modification.

This message and any attachment are confidential and
intended solely to its
addressees. If you are not the intended recipient please
cancel it and
inform immediately the sender. Any unauthorised copy or
dissemination is
prohibited. Electronic messages may be altered: Astellia
shall not be
liable for those circumstances.

------------------------------------------------------------
----------------------------------------




_______________________________________________
Megaco mailing list
Megacoietf.org
https:/
/www1.ietf.org/mailman/listinfo/megaco





_______________________________________________
Megaco mailing list
Megacoietf.org
https:/
/www1.ietf.org/mailman/listinfo/megaco