You are now subscribed to the ACCESS-L list

Mon, 1 May 2006 12:46:12

Your  subscription  to  the  ACCESS-L  list  (Microsoft 
Access  Database
Discussion List) has been accepted.

                             *** NOTICE ***

DO NOT  REPLY TO THIS  MESSAGE WITH  LISTSERV COMMANDS.
Please  read this
message carefully for  instructions on how to send  commands
to LISTSERV.
Thank you.

IMPORTANT:  You subscribed  as  Mick English 
<englishyahoo.com>. If  your
email address  changes you will  not be able  to change your
 settings or
sign off. This  can happen if your mail provider  changes
their system or
if   you   change   email   programs.   If   this   happens,
  write   to
ACCESS-L-requestPEACH.EASE.LSOFT.COM  to   communicate 
with   the  list
owner(s).

Please save this message for future  reference, especially
if this is the
first time you subscribe to an  electronic mailing list. If
you ever need
to  leave the  list,  you  will find  the  necessary
instructions  below.
Perhaps  more importantly,  saving a  copy of  this message 
(and of  all
future subscription notices  from other mailing lists) in  a
special mail
folder will give you instant access to the list of mailing
lists that you
are subscribed  to. This may  prove very useful the  next
time you  go on
vacation and  need to leave  the lists temporarily so  as
not to  fill up
your  mailbox while  you  are away!  You should  also  save
the  "welcome
messages" from the  list owners that you will 
occasionally receive after
subscribing to a new list.

To send  a message to  all the people  currently subscribed
to  the list,
just send mail to  ACCESS-LPEACH.EASE.LSOFT.COM. This
is called "sending
mail to the list", because you send mail to a single
address and LISTSERV
makes  copies  for all  the  people  who  have subscribed. 
This  address
(ACCESS-LPEACH.EASE.LSOFT.COM) is  also called  the
"list  address". You
must  never try  to send  any command  to that  address, as 
it would  be
distributed to all  the people who have subscribed. All 
commands must be
sent to the "LISTSERV address", LISTSERVPEACH.EASE.LSOFT.COM. It is very
important to understand  the difference between the  two,
but fortunately
it is  not complicated. The  LISTSERV address is  like a FAX
 number that
connects you  to a  machine, whereas  the list address  is
like  a normal
voice line connecting you to a person. If you make a mistake
and dial the
FAX number  when you  wanted to talk  to someone on  the
phone,  you will
quickly realize  that you used the  wrong number and call 
again. No harm
will have been done. If on the  other hand you accidentally
make your FAX
call  someone's  voice  line,  the  person receiving  the 
call  will  be
inconvenienced, especially if your FAX then re-dials every 5
minutes. The
fact that  most people  will eventually  connect the  FAX
machine  to the
voice line to  allow the FAX to  go through and make the 
calls stop does
not mean  that you  should continue  to send FAXes  to the 
voice number.
People would just get mad at you.  It works pretty much the
same way with
mailing  lists, with  the difference  that  you are  calling
hundreds  or
thousands of people  at the same time, and consequently  you
can expect a
lot of people to get upset if  you consistently send
commands to the list
address.

You  may leave  the list  at  any time  by sending  a
"SIGNOFF  ACCESS-L"
command to LISTSERVPEACH.EASE.LSOFT.COM. You  can also tell
LISTSERV how
you want it to  confirm the receipt of messages you send  to
the list. If
you do  not trust  the system,  send a "SET  ACCESS-L
REPRO"  command and
LISTSERV will send you  a copy of your own messages, so 
that you can see
that the  message was  distributed and  did not get  damaged
on  the way.
After a while  you may find that this is  getting annoying,
especially if
your mail program does not tell you  that the message is
from you when it
informs you that new  mail has arrived from ACCESS-L. If 
you send a "SET
ACCESS-L  ACK   NOREPRO"  command,  LISTSERV   will 
mail  you   a  short
acknowledgement  instead,  which  will  look different  in 
your  mailbox
directory. With most mail programs you will know immediately
that this is
an  acknowledgement  you  can  read  later. Finally,  you 
can  turn  off
acknowledgements completely with "SET ACCESS-L NOACK
NOREPRO".

Following  instructions from  the list  owner, your 
subscription options
have been set  to "NOFILES NOREPRO DIGESTS
NOMIME" rather  than the usual
LISTSERV defaults. For more  information about subscription
options, send
a "QUERY ACCESS-L" command to LISTSERVPEACH.EASE.LSOFT.COM.

Contributions sent to this list are automatically archived.
You can get a
list  of the  available  archive  files by  sending  an
"INDEX  ACCESS-L"
command to LISTSERVPEACH.EASE.LSOFT.COM. You  can then order
these files
with  a "GET  ACCESS-L  LOGxxxx" command,  or 
using LISTSERV's  database
search facilities. Send  an "INFO DATABASE"
command  for more information
on the latter.

This  list is  available  in digest  form.  If you  wish  to
receive  the
digested  version of  the  postings,  just issue  a  SET
ACCESS-L  DIGEST
command.

More  information on  LISTSERV  commands  can be  found  in
the  LISTSERV
reference  card, which  you can  retrieve  by sending  an
"INFO  REFCARD"
command to LISTSERVPEACH.EASE.LSOFT.COM.