Power Macintosh 9500 / 132

Hello Michael,

Follow below my commands:

OBS: For all commands that i tried the LED blink ok.

0 >   ok
0 >   ok
0 >   ok
0 > boot scsi-int/sd6  can't OPEN: scsi-int/sd6
 ok
0 > boot scsi-int/sd6:0  can't OPEN: scsi-int/sd6:0
 ok
0 > boot scsi-int/sd6:0 netbsd.macppc  can't OPEN:
scsi-int/sd6:0
 ok
0 > boot scsi-int/sd6:,ofwboot.xcf netbsd.macppc  can't OPEN:
scsi-int/sd6:,ofwboot.xcf
 ok
0 > boot scsi-int/sd6:0,ofwboot.xcf netbsd.macppc  can't LOAD
from this device
 ok
0 > boot scsi-int/sd6:,ofwboot.xcf netbsd.macppc  can't OPEN:
scsi-int/sd6:,ofwboot.xcf
 ok
0 > boot scsi-int/sd6:0,ofwboot.xcf netbsd.macppc can't OPEN:
scsi-int/sd6:0,ofwboot.xcf
 ok
0 > boot scsi-int/sd6:0,ofwboot.xcf;1 netbsd.macppc;1  can't
OPEN:
scsi-int/sd6:0,ofwboot.xcf;1
 ok
0 > boot scsi-int/sd6:0,ofwboot.xcf;1 netbsd.macppc;1  can't
OPEN:
scsi-int/sd6:0,ofwboot.xcf;1
 ok
0 > boot scsi-int/sd6:,ofwboot.xcf;1 netbsd.macppc;1  can't
OPEN:
scsi-int/sd6:,ofwboot.xcf;1
 ok


OBS: When i put in my second Cd-rom device on BUS 0 ( scsi )
the
errors change like that:


0 > boot scsi/sd6:0                    # it command doesnt
return me anything.

0 > boot scsi/sd6:0 netbsd.macppc      # it command doesnt
return me anything.

0 > boot scsi/sd6:0,ofwboot.xcf netbsd.macppc bad
partition number,
using 0_          # it command doesnt return me the prompt.

0 > boot scsi/sd6:0,ofwboot.xcf;1 netbsd.macppc;1 bad
partition
number, using 0_      # it command doesnt return me the
prompt.

0 > boot scsi/sd6:,ofwboot.xcf netbsd.macppc bad partition
number,
using 0_            # it command doesnt return me the
prompt.

0 > dev scsi   ok
0 > show-children
Target 0
  Unit 0  Disk          QUANTUM FIREBALL ST3.2S OFOC
Target 2
  Unit 0  Disk          QUANTUM FIREBALL ST3.2S OFOC
Target 6
  Unit 0  Removable Read Only device    TOSHIBA CD-ROM
XM-4101TA0064
 ok

I was exactly what i did.

I appreciate some helps.

Thanks a lot,

Marcos


On 10/30/06, Michael Lorenz <macallannetbsd.org> wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hello,
>
> On Oct 30, 2006, at 06:54, Marcos Onisto wrote:
>
> > I inverted my Cd-rom's devices and i got different
results. When i try
> > to boot on my second Cd-rom, i can see Cd-rom's
Led blink quicky, but
> > i happen only when i try the boot command or i got
the other error
> > about "error on partition 0" or it's
stop and not return me a error.
>
> So what exactly did you do? Did you try partition 0 or
:,ofwboot.xcf?
> Anyway, the drive's LED blinking shows that you're on
the right way.
>
> > I appreciate some helps.
>
> Then tell us EXACTLY what you did and EXACTLY what
happened as a result.
>
> have fun
> Michael
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.2.4 (Darwin)
>
>
iQEVAwUBRUYM88pnzkX8Yg2nAQICqAf9FgqwZGtTTMdrvUfvN53k1aqpajiJ
dN+v
>
zONz0qG50m4XOq9nx6YxIRUGKIUTNCqcymjiGNzjHCMAzCJOGxi4PRSUSq72
8plj
>
B1YZAzS+amHXm1ZRbZYfjHGYrkAPNaBAGEg6pJh5EtPupIwYoyjPbIKklyg9
iZSN
>
RmxO26T6U9Y1mxd9kmwBAhXePgzVoy5nD2ntd7zZHS/69NMsqTyzN1H5woHk
QSiZ
>
AQPb9d16s9gjwpSyq0p0w6kk2G12wa2UhKAHBc5w8e1J7TsQXtFCwAFkdR69
yoPK
>
xGW/fA4arzXv3H1EEHTYkjXtgKIQhIGXev02Jtf0KPa8/JgyWI++eg==
> =VcTV
> -----END PGP SIGNATURE-----
>
>