Hi,
I'm trying to get my wireless card working under 4.1. The
machine is
a Sony VAIO PCG-V505BCP. It has an Intersil PRISM3 PCI
card that
works fine under linux. According to the wi(4) manpage,
this card
appears to be supported. Its interface doesn't show up in
the output
of ifconfig, however.
My dmesg follows, but from this excerpt is appears that I'm
having
some irq problems:
wi0 at pci2 dev 2 function 0 "Intersil PRISM3"
rev
0x01pci_intr_map: no mapping for pin A
: couldn't map interrupt
I've worked on this problem for many hours now, following up
whatever
suggestions looked promising from the list archives.
1) I've tried playing with the flags to PCIBIOS.
2) I've tried setting the irq manually with
boot_config(8).
3) I've upgraded the card's firmware, which involved
reinstalling
linux and then obsd :(
Nothing has affected the message above, though it is
possible that I
screwed up the above fixes somehow, since I'm brand new to
OpenBSD.
Any suggestions would be greatly appreciated. Thanks in
advance !
Ben
OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007
deraadt i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENER
IC
cpu0: Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz
("GenuineIntel"
686-class) 1.99 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT
,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-I
D,xTPR
real mem = 535851008 (523292K)
avail mem = 481222656 (469944K)
using 4278 buffers containing 26918912 bytes (26288K) of
memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 04/22/03, BIOS32 rev.
0
0xfd891, SMBIOS rev. 2.31 0xd8010 (15 entries)
bios0: Sony Corporation PCG-V505BCP(UC)
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 0xfd890/0x770
pcibios0: PCI IRQ Routing Table rev 1.0
0xfdf50/144 (7 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel
82371FB ISA" rev 0x00)
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd8000/0x4000!
0xdc000/0x4000!
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845 Host"
rev 0x04
ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP"
rev 0x04
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M6
LY" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM
Hub-to-PCI" rev 0x42
pci2 at ppb1 bus 2
wi0 at pci2 dev 2 function 0 "Intersil PRISM3" rev
0x01pci_intr_map:
no mapping for pin A
: couldn't map interrupt
cbb0 at pci2 dev 5 function 0 "Ricoh 5C475
CardBus" rev 0xb8: irq 3
"Ricoh 5C551 Firewire" rev 0x00 at pci2 dev 5
function 1 not configured
ohci0 at pci2 dev 7 function 0 "NEC USB" rev 0x43:
irq 9, version 1.0,
legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci2 dev 7 function 1 "NEC USB" rev 0x43:
irq 10, version
1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci2 dev 7 function 2 "NEC USB" rev 0x04:
irq 3
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
fxp0 at pci2 dev 8 function 0 "Intel PRO/100 VE"
rev 0x42, i82562: irq
10, address 08:00:46:ad:b4:15
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x0,
lattimer 0x20
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801CAM
LPC" rev 0x02: SpeedStep
pciide0 at pci0 dev 31 function 1 "Intel 82801CAM
IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured
to comp
atibility
wd0 at pciide0 channel 0 drive 0: <IC25N040ATMR04-0>
wd0: 16-sector PIO, LBA48, 38154MB, 78140160 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, UJDA745
DVD/CDRW, 1.01> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801CA/CAM
SMBus" rev
0x02pci_intr_map: no mapping for pin B
: polling
iic0 at ichiic0
auich0 at pci0 dev 31 function 5 "Intel 82801CA/CAM
AC97" rev 0x02:
irq 9, ICH3 AC97
ac97: codec id 0x594d4803 (Yamaha YMF753-S)
ac97: codec features 18 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801CA/CAM Modem" rev 0x02 at pci0 dev 31
function 6 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using
exception 16
biomask effd netmask effd ttymask ffff
pctr: user-level cycle counter enabled
umass0 at uhub1 port 2 configuration 1 interface 0
umass0: Sony USB Memory Stick Slot, rev 1.10/1.90, addr 2
umass0: using ATAPI over CBI with CCI
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <Sony, MSC-U03, 2.00>
SCSI0 0/direct removable
sd0: drive offline
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
|