Smoke 31875 FAIL(m) MSWin32 WinXP/.Net SP2 (x86/2 cpu)

Automated smoke report for 5.10.0 patch 31875
maldoror.bath.planit.group: Intel(R) Core(TM)2 CPU 6700 
2.66GHz(~2659 MHz) (x86/2 cpu)
    on        MSWin32 - WinXP/.Net SP2
    using     ? unknown cc version 
    smoketime 1 minute 41 seconds (average 5.050 seconds)

Summary: FAIL(m)

O = OK  F = Failure(s), extended report at the bottom
X = Failure(s) under TEST but not under harness
? = still running or test results not (yet) available
Build failures during:       - = unknown or N/A
c = Configure, m = make, M = make (after miniperl), t = make
test-prep

   31875     Configuration (common) -DCCTYPE=MSVC70FREE
-DINST_TOP=$(INST_DRV)Smokedoesntexist
-----------
---------------------------------------------------------
m m         
m m         -Dusemymalloc
m m         -Duselargefiles
m m         -Duselargefiles -Dusemymalloc
m m         -Duseithreads -Uuseimpsys
m m         -Duseithreads -Uuseimpsys -Dusemymalloc
m m         -Duseithreads -Uuseimpsys -Duselargefiles
m m         -Duseithreads -Uuseimpsys -Duselargefiles
-Dusemymalloc
m m         -Duseithreads
m m         -Duseithreads -Duselargefiles
| +--------- -DDEBUGGING
+----------- no debugging

Locally applied patches:
    DEVEL
    SMOKE31875

MANIFEST did not declare 'PATCHLEVEL.BAK'
MANIFEST did not declare 'POLICY.SH'
MANIFEST did not declare 'WIN32/SMOKE.MK'

Compiler messages(MSWin32):
c:SmokesVC7Ftsbleadperlperl.h(4428) : error C2059:
syntax error : ';'

-- 
Report by Test::Smoke v1.19_86 build 1044 running on perl
5.9.5
(Reporter v0.027 / Smoker v0.032)

On Sun, Sep 23, 2007 at 10:05:00PM +0100, Steve Hay wrote:
> Automated smoke report for 5.10.0 patch 31875
> maldoror.bath.planit.group: Intel(R) Core(TM)2 CPU 6700

2.66GHz(~2659 MHz) (x86/2 cpu)

> Compiler messages(MSWin32):
> c:SmokesVC7Ftsbleadperlperl.h(4428) : error C2059:
syntax error : ';'

Odd. That was fixed by change 31876. Why is your smoker's
source tree about
a week old?

Nicholas Clark

Nicholas Clark wrote:
> On Sun, Sep 23, 2007 at 10:05:00PM +0100, Steve Hay
wrote:
>> Automated smoke report for 5.10.0 patch 31875
>> maldoror.bath.planit.group: Intel(R) Core(TM)2 CPU
6700 
>> 2.66GHz(~2659 MHz) (x86/2 cpu) 
> 
>> Compiler messages(MSWin32):
>> c:SmokesVC7Ftsbleadperlperl.h(4428) : error
C2059: syntax error
>> : ';' 
> 
> Odd. That was fixed by change 31876. Why is your
smoker's source tree
> about a week old?

Hmm. Nasty. I updated my Cygwin installation (used for the
rsync of the
smoke source tree) on Friday afternoon, and it seems that
the three
smokes over the weekend (Fri, Sat & Sun evening) have
all failed to
rsync their source trees. They therefore ran with the
sources that were
in place from the previous week since these smokes
(BCC/GCC/VC7) only
run once a week.

Not sure what to do about it, though. The new version of
Cygwin / rsync
just doesn't seem to like the command that Test::Smoke uses,
despite it
always having worked in the past:

C:Temp>C:cygwinbinrsync.EXE -avzL --delete -v
rsync://ftp.linux.activestate.com/perl-current
C:SmokesVC7Ftsbleadperl
The source and destination cannot both be remote.
rsync error: syntax or usage error (code 1) at
/home/lapo/packaging/tmp/rsync-2.6.9/main.c(1068)
[receiver=2.6.9]

It only wants to play ball if I 'cd' to the parent of the
target
directory and specify the relative path from there:

C:SmokesVC7Fts>C:cygwinbinrsync.EXE -avzL --delete
-v
rsync://ftp.linux.activestate.com/perl-current bleadperl
opening tcp connection to ftp.linux.activestate.com port
873
opening connection using --server --sender -vvlLogDtprz .
perl-5.8.x
receiving file list ...

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Steve Hay wrote:
[snip]
> Hmm. Nasty. I updated my Cygwin installation (used for
the rsync of the
> smoke source tree) on Friday afternoon, and it seems
that the three
> smokes over the weekend (Fri, Sat & Sun evening)
have all failed to
> rsync their source trees. They therefore ran with the
sources that were
> in place from the previous week since these smokes
(BCC/GCC/VC7) only
> run once a week.
> 
> Not sure what to do about it, though. The new version
of Cygwin / rsync
> just doesn't seem to like the command that Test::Smoke
uses, despite it
> always having worked in the past:

*Really* nasty, so I fixed Test::Smoke.

It now chdir()s into the build dir and rsync()s to '.'

Please rsync latest Test::Smoke from
rsync://source.test-smoke.org/ts-maint

Abe
- --
 _  | The data on your hard drive is out of balance. (#299)
( ) |
 X  |
/  |
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (Darwin)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org


iD8DBQFG94u50u0nt7xxiCIRAr8oAJ900vbiIDeqraYC1149efosaWILFgCd
F8tg
7zXO2oCC7Q/r1TRbtJ7OhM0=
=fTLa
-----END PGP SIGNATURE-----

Abe Timmerman wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
> 
> Steve Hay wrote:
> [snip]
>> Hmm. Nasty. I updated my Cygwin installation (used
for the rsync of
>> the smoke source tree) on Friday afternoon, and it
seems that the
>> three smokes over the weekend (Fri, Sat & Sun
evening) have all
>> failed to rsync their source trees. They therefore
ran with the
>> sources that were in place from the previous week
since these smokes
>> (BCC/GCC/VC7) only run once a week. 
>> 
>> Not sure what to do about it, though. The new
version of Cygwin /
>> rsync just doesn't seem to like the command that
Test::Smoke uses,
>> despite it always having worked in the past:
> 
> *Really* nasty, so I fixed Test::Smoke.
> 
> It now chdir()s into the build dir and rsync()s to '.'
> 
> Please rsync latest Test::Smoke from
> rsync://source.test-smoke.org/ts-maint

Thanks for the quick fix!  I was on the brink of downgrading
my rsync
from 2.6.9 back to 2.6.6, but now I won't bother.

I rsynced ts-maint (rev 1110) but I get a couple of test
failures:

C:TempSmoke>perl -Mblib tsyncer_rsync.t
1..33
ok 1 - use Test::Smoke::Syncer;
ok 2 - No error on no type
ok 3 - The object isa Test::Smoke::Syncer::Rsync
ok 4 -  exists
ok 5 -  value
ok 6 -  exists
ok 7 -  value
ok 8 -  exists
ok 9 -  value
ok 10 -  exists
ok 11 -  value
ok 12 - No error on type 'rsync'
ok 13 - The object isa Test::Smoke::Syncer::Rsync
ok 14 -  exists
not ok 15 -  value C:usrlocalsrcbleadperlperl
#   Failed test ' value
C:usrlocalsrcbleadperlperl'
#   at tsyncer_rsync.t line 45.
#          got: 'C:usrlocalsrcbleadperlperl'
#     expected: 'usrlocalsrcbleadperlperl'
ok 16 -  exists
ok 17 -  value -az --delete
ok 18 -  exists
ok 19 -  value rsync
ok 20 -  exists
ok 21 -  value
ftp.linux.ActiveState.com::perl-current
ok 22 - No errror when options passed as hashref
ok 23 - The object isa Test::Smoke::Syncer::Rsync
ok 24 -  exists
not ok 25 -  value C:usrlocalsrcbleadperlperl
#   Failed test ' value
C:usrlocalsrcbleadperlperl'
#   at tsyncer_rsync.t line 65.
#          got: 'C:usrlocalsrcbleadperlperl'
#     expected: 'usrlocalsrcbleadperlperl'
ok 26 -  exists
ok 27 -  value -az --delete
ok 28 -  exists
ok 29 -  value rsync
ok 30 -  exists
ok 31 -  value
ftp.linux.ActiveState.com::perl-current
ok 32 - Error on unknown type
ok 33 - Error message on unknown type
# Looks like you failed 2 tests of 33.