pcons at mainbus0 not configured

Hi,

After successfully installed OpenBSD 4.1 on a SunFire V100,
I
am getting the following error at boot time: `pcons at
mainbus0
not configured`, and the system stops booting at this
point.
Any suggestions?

mufurcz

------------------------------------------------------------
------------------------------

ok boot disk
Boot device: /pci1f,0/ided/disk2,0  File
and args:
OpenBSD IEEE 1275 Bootblock 1.1
..>> OpenBSD 4.1 (obj) #1: Wed Mar  7 02:44:33 MST
2007
    deraadtsparc64.openbsd.org:/usr/src/sys/arch/sparc64/stand/o
fwboot/obj
: trying bsd...
Booting /pci1f,0/ided/disk2,0:a/bsd
48702960x1000000+1798320x1800000+40144720x182be78
symbols  0xfff00280 58+285984+170452 start=0x1000000
[ using 457144 bytes of bsd ELF symbol table ]
console is /pci1f,0/isa7/serial0,3f8
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All
rights reserved.
Copyright (c) 1995-2007 OpenBSD. All rights reserved.  
http://www.OpenBSD.org
OpenBSD 4.1 (GENERIC) #1099: Sat Mar 10 19:18:09 MST 2007
    deraadtsparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile
/GENERIC
total memory = 2147483648
avail memory = 1949777920
using 13107 buffers containing 107372544 bytes of memory
bootpath: /pci1f,0/ided,0/disk2,0
mainbus0 (root): Sun Fire V100 (UltraSPARC-IIe 500MHz)
cpu0 at mainbus0: SUNW,UltraSPARC-IIe (rev 1.4)  500 MHz,
version 0 FPU
cpu0: physical 16K instruction (32 b/l), 16K data (32 b/l),
256K 
external (64 b/l)
psycho0 at mainbus0: SUNW,sabre, impl 0, version 0, ign 7c0
psycho0: bus range 0-0, PCI bus 0
psycho0: dvma map 60000000-7fffffff, iotdb acb6000-ad36000
pci0 at psycho0
ebus0 at pci0 dev 7 function 0 "Acer Labs M1533
ISA" rev 0x00
"dma" at ebus0 addr 0-ffff ipl 42 not configured
rtc0 at ebus0 addr 70-71: m5819
power0 at ebus0 addr 2000-2007 ipl 35: can't map register
space
"SUNW,lomh" at ebus0 addr 8010-8011 ipl 42 not
configured
com0 at ebus0 addr 3f8-3ff ipl 43: ns16550a, 16 byte fifo
com0: console
com1 at ebus0 addr 2e8-2ef ipl 43: ns16550a, 16 byte fifo
"flashprom" at ebus0 addr 0-7ffff not configured
"Acer Labs M7101 Power" rev 0x00 at pci0 dev 3
function 0 not configured
dc0 at pci0 dev 12 function 0 "Davicom DM9102" rev
0x31: ivec 0x7c6, 
address 00:03:ba:13:13:61
amphy0 at dc0 phy 1: DM9102 10/100 PHY, rev. 0
dc1 at pci0 dev 5 function 0 "Davicom DM9102" rev
0x31interrupt_vector: 
spurious vector 7de at pil 13
: ivec 0x7dc, address 00:03:ba:13:13:62
amhy1 at dc1 phy 1: DM9102 10/100 PHY, rev. 0
ohci0 at pci0 dev 10 function 0 "Acer Labs M5237
USB" rev 0x03: ivec 
0x7e4, version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pciide0 at pci0 dev 13 function 0 "Acer Labs M5229 UDMA
IDE" rev 0xc3: 
DMA, channel 0 configured to native-PCI, channel 1
configured to native-PCI
pciide0: using ivec 0x7cc for native-PCI interrupt
pciide0: channel 0 disabled (no drives)
wd0 at pciide0 channel 1 drive 0: <ST340014A>
wd0: 16-sector PIO, LBA48, 38166MB, 78165360 sectors
atapiscsi0 at pciide0 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-N, 1.6A>
SCSI0 5/cdrom removable
wd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
cd0(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
pcons at mainbus0 not configured

> After successfully installed OpenBSD 4.1 on a SunFire
V100, I
> am getting the following error at boot time: `pcons at
mainbus0
> not configured`, and the system stops booting at this
point.

There have been trouble with cd-rom drives generating
interrupt floods
on some SunFire.

If you unplug the cd-rom drive, does the system boot
further?

Miod